Cherry Trail Z8750 USB3.0 xhci Compatibility USB3.0 flash issue on Android 7.1

Hello, We are facing an issue that Cherry Trail Z8750 USB3.0 xhci root hub has USB3.0 flashes compatibility issue while Android 7.1 boots up.

some of usb3.0 flashes 100% cannot be recognized while Android 7.1 boots up.

However, after android 7.1 is boot and ready, I unplug USB3.0 flash and plug in again the USB3.0 flash can be recognized.

I use dmesg to dump debug message and I found that xhci hcd root hub CAN recognized USB3.0 flash at beginning, but there always is a remove INT occurred. the driver starts do debounce check and remove USB3.0 flash although the USB3.0 flash is still attached on my device.

below is the debug message, it shows

at 6.923130 sec the driver found an USB3.0 at hub 2-0:1.0 and finish connection

at 7.202915 sec the driver found an Hub change at hub 2-0:1.0 and starts denounce check with no USB3.0 device result.

the USB3.0 device is present or not always come from xhci hcd root hub.

Although I tried reset root hub or USB device, USB3.0 flash always cannot be recognized while Android boots up.

I also install and test my device on Windows 10 with the Same USB3.0 Flashes, they are work perfectly!!

Is there any work around solution?

dmesg

[ 0.000000] Initializing cgroup subsys cpuset

[ 0.000000] Initializing cgroup subsys cpu

[ 0.000000] Initializing cgroup subsys cpuacct

[ 0.000000] Linux version 3.14.79-x86_64-svn6727 (Flytech@ANDROID) (gcc version 4.9.2 (GCC) ) #131 SMP PREEMPT Wed Jul 25 09:17:03 CST 2018

[ 0.000000] Command line: androidboot.bootloader=d420v101_d420-10103__kernelflinger-04_15-userdebug androidboot.diskbus=10.0 androidboot.verifiedbootstate=green androidboot.bootreason=power_button_pressed androidboot.serialno=androidd410123456789 g_ffs.iSerialNumber=androidd410123456789 enforcing=0 androidboot.selinux=permissive loglevel=5 androidboot.hardware=cht_rvp firmware_class.path=/system/etc/firmware memmap=4M$0x5c400000 vga=current i915.modeset=1 drm.vblankoffdelay=1 i915.fastboot=1 thermal.off=1 console=ttyS0,115200n8 pstore.backend=ramoops intel_pstore_pram.record_size=0x8000

[ 0.000000] e820: BIOS-provided physical RAM map:

[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable

[ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS

[ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009ffff] usable

[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001effffff] usable

[ 0.000000] BIOS-e820: [mem 0x000000001f000000-0x00000000201fffff] reserved

[ 0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000007a49dfff] usable

[ 0.000000] BIOS-e820: [mem 0x000000007a49e000-0x000000007adddfff] reserved

[ 0.000000] BIOS-e820: [mem 0x000000007adde000-0x000000007aeddfff] ACPI NVS

[ 0.000000] BIOS-e820: [mem 0x000000007aede000-0x000000007af1dfff] ACPI data

[ 0.000000] BIOS-e820: [mem 0x000000007af1e000-0x000000007bffffff] usable

[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000feafffff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed06000-0x00000000fed06fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed09fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fedbffff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved

[ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved

[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable

[ 0.000000] NX (Execute Disable) protection: active

[ 0.000000] e820: user-defined physical RAM map:

[ 0.000000] user: [mem 0x0000000000000000-0x000000000008efff] usable

[ 0.000000] user: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS

[ 0.000000] user: [mem 0x0000000000090000-0x000000000009ffff] usable

[ 0.000000] user: [mem 0x0000000000100000-0x000000001effffff] usable

[ 0.000000] user: [mem 0x000000001f000000-0x00000000201fffff] reserved

[ 0.000000] user: [mem 0x0000000020200000-0x000000005c3fffff] usable

[ 0.000000] user: [mem 0x000000005c400000-0x000000005c7fffff] reserved

[ 0.000000] user: [mem 0x000000005c800000-0x000000007a49dfff] usable

[ 0.000000] user: [mem 0x000000007a49e000-0x000000007adddfff] reserved

[ 0.000000] user: [mem 0x000000007adde000-0x000000007aeddfff] ACPI NVS

[ 0.000000] user: [mem 0x000000007aede000-0x000000007af1dfff] ACPI data

[ 0.000000] user: [mem 0x000000007af1e000-0x000000007bffffff] usable

[ 0.000000] user: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved

[ 0.000000] user: [mem 0x00000000fea00000-0x00000000feafffff] reserved

[ 0.000000] user: [mem 0x00000000fec00000-0x00000000fec00fff] reserved

[ 0.000000] user: [mem 0x00000000fed01000-0x00000000fed01fff] reserved

[ 0.000000] user: [mem 0x00000000fed03000-0x00000000fed03fff] reserved

[ 0.000000] user: [mem 0x00000000fed06000-0x00000000fed06fff] reserved

[ 0.000000] user: [mem 0x00000000fed08000-0x00000000fed09fff] reserved

[ 0.000000] user: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved

[ 0.000000] user: [mem 0x00000000fed80000-0x00000000fedbffff] reserved

[ 0.000000] user: [mem 0x00000000fee00000-0x00000000fee00fff] reserved

[ 0.000000] user: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved

[ 0.000000] user: [mem 0x0000000100000000-0x000000017fffffff] usable

[ 0.000000] efi: EFI v2.40 by INSYDE Corp.

[ 0.000000] efi: ACPI 2.0=0x7af1d014 SMBIOS=0x7a56d000

[ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x000000000008f000) (0MB)

[ 0.000000] efi: mem01: type=10, attr=0xf, range=[0x000000000008f000-0x0000000000090000) (0MB)

[ 0.000000] efi: mem02: type=2, attr=0xf, range=[0x0000000000090000-0x0000000000092000) (0MB)

[ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000092000-0x000000000009f000) (0MB)

[ 0.000000] efi: mem04: type=2, attr=0xf, range=[0x000000000009f000-0x00000000000a0000) (0MB)

[ 0.000000] efi: mem05: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000632000) (5MB)

[ 0.000000] efi: mem06: type=7, attr=0xf, range=[0x0000000000632000-0x0000000001000000) (9MB)

[ 0.000000] efi: mem07: type=2, attr=0xf, range=[0x0000000001000000-0x0000000002ad0000) (26MB)

[ 0.000000] efi: mem08: type=7, attr=0xf, range=[0x0000000002ad0000-0x000000001f000000) (453MB)

[ 0.000000] efi: mem09: type=0, attr=0xf, range=[0x000000001f000000-0x0000000020200000) (18MB)

[ 0.000000] efi: mem10: type=7, attr=0xf, range=[0x0000000020200000-0x000000003fffc000) (509MB)

[ 0.000000] efi: mem11: type=2, attr=0xf, range=[0x000000003fffc000-0x0000000040000000) (0MB)

[ 0.000000] efi: mem12: type=7, attr=0xf, range=[0x0000000040000000-0x0000000073d3e000) (829MB)

[ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x0000000073d3e000-0x0000000073d5e000) (0MB)

[ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x0000000073d5e000-0x00000000759b7000) (28MB)

[ 0.000000] efi: mem15: type=2, attr=0xf, range=[0x00000000759b7000-0x00000000766c5000) (13MB)

[ 0.000000] efi: mem16: type=1, attr=0xf, range=[0x00000000766c5000-0x0000000076c9e000) (5MB)

[ 0.000000] efi: mem17: type=7, attr=0xf, range=[0x0000000076c9e000-0x0000000076d60000) (0MB)

[ 0.000000] efi: mem18: type=2, attr=0xf, range=[0x0000000076d60000-0x0000000076d66000) (0MB)

[ 0.000000] efi: mem19: type=7, attr=0xf, range=[0x0000000076d66000-0x0000000076d67000) (0MB)

[ 0.000000] efi: mem20: type=2, attr=0xf, range=[0x0000000076d67000-0x0000000076d69000) (0MB)

[ 0.000000] efi: mem21: type=7, attr=0xf, range=[0x0000000076d69000-0x0000000076d6a000) (0MB)

[ 0.000000] efi: mem22: type=2, attr=0xf, range=[0x0000000076d6a000-0x0000000076d6d000) (0MB)

[ 0.000000] efi: mem23: type=7, attr=0xf, range=[0x0000000076d6d000-0x0000000076d70000) (0MB)

[ 0.000000] efi: mem24: type=2, attr=0xf, range=[0x0000000076d70000-0x0000000076d73000) (0MB)

[ 0.000000] efi: mem25: type=7, attr=0xf, range=[0x0000000076d73000-0x0000000076d9c000) (0MB)

[ 0.000000] efi: mem26: type=2, attr=0xf, range=[0x0000000076d9c000-0x0000000076d9e000) (0MB)

[ 0.000000] efi: mem27: type=7, attr=0xf, range=[0x0000000076d9e000-0x000000007843e000) (22MB)

[ 0.000000] efi: mem28: type=4, attr=0xf, range=[0x000000007843e000-0x0000000078d69000) (9MB)

[ 0.000000] efi: mem29: type=7, attr=0xf, range=[0x0000000078d69000-0x0000000078d6a000) (0MB)

[ 0.000000] efi: mem30: type=4, attr=0xf, range=[0x0000000078d6a000-0x000000007949e000) (7MB)

[ 0.000000] efi: mem31: type=7, attr=0xf, range=[0x000000007949e000-0x000000007a06d000) (11MB)

[ 0.000000] efi: mem32: type=3, attr=0xf, range=[0x000000007a06d000-0x000000007a49e000) (4MB)

[ 0.000000] efi: mem33: type=5, attr=0x800000000000000f, range=[0x000000007a49e000-0x000000007a52e000) (0MB)

[ 0.000000] efi: mem34: type=6, attr=0x800000000000000f, range=[0x000000007a52e000-0x000000007a7de000) (2MB)

[ 0.000000] efi: mem35: type=0, attr=0xf, range=[0x000000007a7de000-0x000000007adde000) (6MB)

[ 0.000000] efi: mem36: type=10, attr=0xf, range=[0x000000007adde000-0x000000007aede000) (1MB)

[ 0.000000] efi: mem37: type=9, attr=0xf, range=[0x000000007aede000-0x000000007af1e000) (0MB)

[ 0.000000] efi: mem38: type=4, attr=0xf, range=[0x000000007af1e000-0x000000007c000000) (16MB)

[ 0.000000] efi: mem39: type=7, attr=0xf, range=[0x0000000100000000-0x0000000180000000) (2048MB)

[ 0.000000] efi: mem40: type=12, attr=0x8000000000000000, range=[0x00000000e0000000-0x00000000e4000000) (64MB)

[ 0.000000] efi: mem41: type=11, attr=0x8000000000000000, range=[0x00000000fea00000-0x00000000feb00000) (1MB)

[ 0.000000] efi: mem42: type=11, attr=0x8000000000000000, range=[0x00000000fec00000-0x00000000fec01000) (0MB)

[ 0.000000] efi: mem43: type=11, attr=0x8000000000000000, range=[0x00000000fed01000-0x00000000fed02000) (0MB)

[ 0.000000] efi: mem44: type=11, attr=0x8000000000000001, range=[0x00000000fed03000-0x00000000fed04000) (0MB)

[ 0.000000] efi: mem45: type=11, attr=0x8000000000000000, range=[0x00000000fed06000-0x00000000fed07000) (0MB)

[ 0.000000] efi: mem46: type=11, attr=0x8000000000000000, range=[0x00000000fed08000-0x00000000fed0a000) (0MB)

[ 0.000000] efi: mem47: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed1d000) (0MB)

[ 0.000000] efi: mem48: type=11, attr=0x8000000000000000, range=[0x00000000fed80000-0x00000000fedc0000) (0MB)

[ 0.000000] efi: mem49: type=11, attr=0x8000000000000000, range=[0x00000000fee00000-0x00000000fee01000) (0MB)

[ 0.000000] efi: mem50: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x0000000100000000) (4MB)

[ 0.000000] SMBIOS 3.0 present.

[ 0.000000] DMI: Insyde CherryTrail/Type2 - Board Product Name, BIOS D420V101(D420-10103) 05/24/2018

[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved

[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable

[ 0.000000] e820: last_pfn = 0x180000 max_arch_pfn = 0x400000000

[ 0.000000] MTRR default type: uncachable

[ 0.000000] MTRR fixed ranges enabled:

[ 0.000000] 00000-9FFFF write-back

[ 0.000000] A0000-FFFFF write-protect

[ 0.000000] MTRR variable ranges enabled:

[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect

[ 0.000000] 1 base 000000000 mask F80000000 write-back

[ 0.000000] 2 base 07E000000 mask FFE000000 uncachable

[ 0.000000] 3 base 07D000000 mask FFF000000 uncachable

[ 0.000000] 4 base 07C800000 mask FFF800000 uncachable

[ 0.000000] 5 base 07C400000 mask FFFC00000 uncachable

[ 0.000000] 6 base 100000000 mask F80000000 write-back

[ 0.000000] 7 disabled

[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106

[ 0.000000] e820: last_pfn = 0x7c000 max_arch_pfn = 0x400000000

[ 0.000000] Scanning 1 areas for low memory corruption

[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576

[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]

[ 0.000000] [mem 0x00000000-0x000fffff] page 4k

[ 0.000000] BRK [0x027eb000, 0x027ebfff] PGTABLE

[ 0.000000] BRK [0x027ec000, 0x027ecfff] PGTABLE

[ 0.000000] BRK [0x027ed000, 0x027edfff] PGTABLE

[ 0.000000] init_memory_mapping: [mem 0x17fe00000-0x17fffffff]

[ 0.000000] [mem 0x17fe00000-0x17fffffff] page 2M

[ 0.000000] BRK [0x027ee000, 0x027eefff] PGTABLE

[ 0.000000] init_memory_mapping: [mem 0x17c000000-0x17fdfffff]

[ 0.000000] [mem 0x17c000000-0x17fdfffff] page 2M

[ 0.000000] init_memory_mapping: [mem 0x100000000-0x17bffffff]

[ 0.000000] [mem 0x100000000-0x17bffffff] page 2M

[ 0.000000] BRK [0x027ef000, 0x027effff] PGTABLE

[ 0.000000] init_memory_mapping: [mem 0x00100000-0x1effffff]

[ 0.000000] [mem 0x00100000-0x001fffff] page 4k

[ 0.000000] [mem 0x00200000-0x1effffff] page 2M

[ 0.000000] init_memory_mapping: [mem 0x20200000-0x5c3fffff]

[ 0.000000] [mem 0x20200000-0x5c3fffff] page 2M

[ 0.000000] BRK [0x027f0000, 0x027f0fff] PGTABLE

[ 0.000000] init_memory_mapping: [mem 0x5c800000-0x7a49dfff]

[ 0.000000] [mem 0x5c800000-0x7a3fffff] page 2M

[ 0.000000] [mem 0x7a400000-0x7a49dfff] page 4k

[ 0.000000] init_memory_mapping: [mem 0x7af1e000-0x7bffffff]

[ 0.000000] [mem 0x7af1e000-0x7affffff] page 4k

[ 0.000000] [mem 0x7b000000-0x7bffffff] page 2M

[ 0.000000] RAMDISK: [mem 0x00100000-0x00631fff]

[ 0.000000] ACPI: RSDP 0x000000007AF1D014 000024 (v02 INTEL )

[ 0.000000] ACPI: XSDT 0x000000007AEEA188 0000DC (v01 INTEL INSYDE 00000003 01000013)

[ 0.000000] ACPI: FACP 0x000000007AF18000 00010C (v05 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: DSDT 0x000000007AEFA000 017412 (v02 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: FACS 0x000000007AE81000 000040

[ 0.000000] ACPI: UEFI 0x000000007AF1C000 000236 (v01 INTEL INSYDE 00000001 ACPI 00040000)

[ 0.000000] ACPI: UEFI 0x000000007AF1A000 000042 (v01 INTEL INSYDE 00000000 ACPI 00040000)

[ 0.000000] ACPI: HPET 0x000000007AF17000 000038 (v01 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: LPIT 0x000000007AF16000 000104 (v01 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: APIC 0x000000007AF15000 00006C (v03 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: MCFG 0x000000007AF14000 00003C (v01 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: PRAM 0x000000007AF13000 000030 (v01 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: SSDT 0x000000007AEF8000 000269 (v01 INTEL UsbCTab 00000003 ACPI 00040000)

[ 0.000000] ACPI: SSDT 0x000000007AEF7000 000763 (v01 INTEL CpuPm 00003000 ACPI 00040000)

[ 0.000000] ACPI: SSDT 0x000000007AEF6000 000290 (v01 INTEL Cpu0Tst 00003000 ACPI 00040000)

[ 0.000000] ACPI: SSDT 0x000000007AEF5000 00017A (v01 INTEL ApTst 00003000 ACPI 00040000)

[ 0.000000] ACPI: SSDT 0x000000007AEF4000 000451 (v01 INTEL Tpm2Tabl 00001000 ACPI 00040000)

[ 0.000000] ACPI: TPM2 0x000000007AEF3000 000034 (v03 INTEL INSYDE 00000000 ACPI 00040000)

[ 0.000000] ACPI: TCPA 0x000000007AEF2000 000032 (v02 INTEL INSYDE 00000000 ACPI 00040000)

[ 0.000000] ACPI: CSRT 0x000000007AF19000 00014C (v00 INTEL INSYDE 00000003 ACPI 00040000)

[ 0.000000] ACPI: OEM0 0x000000007AEF1000 000084 (v05 INTEL BATTERY 00000005 ACPI 00040000)

[ 0.000000] ACPI: OEM1 0x000000007AEF0000 000040 (v01 INTEL ENRGYMGT 00000005 ACPI 00040000)

[ 0.000000] ACPI: PIDV 0x000000007AEEF000 0000DC (v02 INTEL PIDV 00000002 ACPI 00040000)

[ 0.000000] ACPI: RSCI 0x000000007AEEE000 00002C (v01 INTEL BOOTSRC 00000000 ACPI 00040000)

[ 0.000000] ACPI: BCFG 0x000000007AEED000 000139 (v01 INTEL INSYDE 00000001 ACPI 00040000)

[ 0.000000] ACPI: FPDT 0x000000007AF12000 000044 (v01 INTEL INSYDE 00000002 ACPI 00040000)

[ 0.000000] ACPI: BGRT 0x000000007AEF9000 000038 (v01 INTEL INSYDE 00000001 ACPI 00040000)

[ 0.000000] ACPI: Local APIC address 0xfee00000

[ 0.000000] [ffffea0000000000-ffffea0005ffffff] PMD -> [ffff88017b600000-ffff88017f5fffff] on node 0

[ 0.000000] Zone ranges:

[ 0.000000] DMA [mem 0x00001000-0x00ffffff]

[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]

[ 0.000000] Normal [mem 0x100000000-0x17fffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00001000-0x0008efff]

[ 0.000000] node 0: [mem 0x00090000-0x0009ffff]

[ 0.000000] node 0: [mem 0x00100000-0x1effffff]

[ 0.000000] node 0: [mem 0x20200000-0x5c3fffff]

[ 0.000000] node 0: [mem 0x5c800000-0x7a49dfff]

[ 0.000000] node 0: [mem 0x7af1e000-0x7bffffff]

[ 0.000000] node 0: [mem 0x100000000-0x17fffffff]

[ 0.000000] On node 0 totalpages: 1023774

[ 0.000000] DMA zone: 64 pages used for memmap

[ 0.000000] DMA zone: 1352 pages reserved

[ 0.000000] DMA zone: 3998 pages, LIFO batch:0

[ 0.000000] DMA32 zone: 7742 pages used for memmap

[ 0.000000] DMA32 zone: 495488 pages, LIFO batch:31

[ 0.000000] Normal zone: 8192 pages used for memmap

[ 0.000000] Normal zone: 524288 pages, LIFO batch:31

[ 0.000000] x86/hpet: Will disable the HPET for this platform because it's not reliable

[ 0.000000] Reserving Intel graphics stolen memory at 0x7cc00000-0x7ebfffff

[ 0.000000] ACPI: PM-Timer IO Port: 0x408

[ 0.000000] ACPI: Local APIC address 0xfee00000

[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)

[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)

[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)

[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)

[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])

[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-114

[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

[ 0.000000] ACPI: IRQ0 used by override.

[ 0.000000] ACPI: IRQ2 used by override.

[ 0.000000] ACPI: IRQ9 used by override.

[ 0.000000] Using ACPI (MADT) for SMP configuration information

[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000

[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs

[ 0.000000] nr_irqs_gsi: 131

[ 0.000000] e820: [mem 0x7ec00000-0xdfffffff] available for PCI devices

[ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1

[ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88017fc00000 s78784 r8192 d23616 u524288

[ 0.000000] pcpu-alloc: s78784 r8192 d23616 u524288 alloc=1*2097152

[ 0.000000] pcpu-alloc: [0] 0 1 2 3

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1006424

[ 0.000000] Kernel command line: androidboot.bootloader=d420v101_d420-10103__kernelflinger-04_15-userdebug androidboot.diskbus=10.0 androidboot.verifiedbootstate=green androidboot.bootreason=power_button_pressed androidboot.serialno=androidd410123456789 g_ffs.iSerialNumber=androidd410123456789 enforcing=0 androidboot.selinux=permissive loglevel=5 androidboot.hardware=cht_rvp firmware_class.path=/system/etc/firmware memmap=4M$0x5c400000 vga=current i915.modeset=1 drm.vblankoffdelay=1 i915.fastboot=1 thermal.off=1 console=ttyS0,115200n8 pstore.backend=ramoops intel_pstore_pram.record_size=0x8000

[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

[ 0.000000] Memory: 3888320K/4095096K available (11069K kernel code, 3230K rwdata, 5552K rodata, 1444K init, 1344K bss, 206776K reserved)

[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.

[ 0.000000] Additional per-CPU info printed with stalls.

[ 0.000000] Offload RCU callbacks from all CPUs

[ 0.000000] Offload RCU callbacks from CPUs: 0-3.

[ 0.000000] NR_IRQS:4352 nr_irqs:1024 16

[ 0.000000] console [ttyS0] enabled

[ 0.000000] allocated 16777216 bytes of page_cgroup

[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups

[ 0.000000] kmemleak: Kernel memory leak detector disabled

[ 0.000000] Maximum core-clock to bus-clock ratio: 0x14

[ 0.000000] Resolved frequency ID: 4, frequency: 80000 KHz

[ 0.000000] TSC runs at 1600000 KHz

[ 0.000000] lapic_timer_frequency = 80000

[ 0.000000] tsc: Detected 1600.000 MHz processor

[ 0.000056] Calibrating delay loop (skipped), value calculated using timer frequency.. 3200.00 BogoMIPS (lpj=1600000)

[ 0.000066] pid_max: default: 32768 minimum: 301

[ 0.000101] ACPI: Core revision 20131218

[ 0.034639] ACPI: All ACPI Tables successfully acquired

[ 0.036158] Security Framework initialized

[ 0.036181] SELinux: Initializing.

[ 0.036211] SELinux: Starting in permissive mode

[ 0.036244] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)

[ 0.036252] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)

[ 0.036716] Initializing cgroup subsys debug

[ 0.036726] Initializing cgroup subsys memory

[ 0.036738] Initializing cgroup subsys freezer

[ 0.036786] CPU: Physical Processor ID: 0

[ 0.036791] CPU: Processor Core ID: 0

[ 0.036797] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'

[ 0.036797] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)

[ 0.056884] mce: CPU supports 6 MCE banks

[ 0.056916] CPU0: Thermal monitoring enabled (TM1)

[ 0.056926] process: using mwait in idle threads

[ 0.056937] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0

[ 0.056937] Last level dTLB entries: 4KB 256, 2MB 16, 4MB 16, 1GB 0

[ 0.056937] tlb_flushall_shift: 6

[ 0.057131] Freeing SMP alternatives memory: 32K (ffffffff82692000 - ffffffff8269a000)

[ 0.060484] ftrace: allocating 38399 entries in 150 pages

[ 0.093164] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1

[ 0.103177] smpboot: CPU0: Intel(R) Atom(TM) x7-Z8750 CPU @ 1.60GHz (fam: 06, model: 4c, stepping: 04)

[ 0.103221] TSC deadline timer enabled

[ 0.103246] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, full-width counters, Intel PMU driver.

[ 0.103271] ... version: 3

[ 0.103275] ... bit width: 40

[ 0.103278] ... generic registers: 2

[ 0.103281] ... value mask: 000000ffffffffff

[ 0.103284] ... max period: 000000ffffffffff

[ 0.103287] ... fixed-purpose events: 3

[ 0.103290] ... event mask: 0000000700000003

[ 0.112266] EM:OEM0 table found, size=132

[ 0.116537] x86: Booting SMP configuration:

[ 0.116547] .... node #0, CPUs: #1

[ 0.133382] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.

[ 0.135613] #2 #3

[ 0.170225] Skipped synchronization checks as TSC is reliable.

[ 0.170307] x86: Booted up 1 node, 4 CPUs

[ 0.170313] smpboot: Total of 4 processors activated (12800.00 BogoMIPS)

[ 0.172462] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)

[ 0.172472] PM: Registering ACPI NVS region [mem 0x7adde000-0x7aeddfff] (1048576 bytes)

[ 0.175246] pinctrl core: initialized pinctrl subsystem

[ 0.175814] regulator-dummy: no parameters

[ 0.175981] RTC time: 1:21:38, date: 07/25/18

[ 0.176091] NET: Registered protocol family 16

[ 0.177704] cpuidle: using governor ladder

[ 0.177711] cpuidle: using governor menu

[ 0.194479] console [pstore-1] enabled

[ 0.194782] pstore: Registered ramoops as persistent store backend

[ 0.194815] ramoops: attached 0x400000@0x7c000000, ecc: 0/0

[ 0.194870] intel_pstore_pram: registered pram device, addr=0x7c000000, size=0x400000

[ 0.195299] ACPI: bus type PCI registered

[ 0.195333] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5

[ 0.195930] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)

[ 0.195969] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820

[ 0.196200] PCI: Using configuration type 1 for base access

[ 0.249565] bio: create slab <bio-0> at 0

[ 0.250652] ACPI: Added _OSI(Module Device)

[ 0.250687] ACPI: Added _OSI(Processor Device)

[ 0.250737] ACPI: Added _OSI(3.0 _SCP Extensions)

[ 0.250788] ACPI: Added _OSI(Processor Aggregator Device)

[ 0.293853] ACPI: SSDT 0x000000007ADD2798 0006E6 (v01 PmRef Cpu0Ist 00003000 INTL 20130117)

[ 0.296187] ACPI: Dynamic OEM Table Load:

[ 0.296319] ACPI: SSDT 0x0000000000000000 0006E6 (v01 PmRef Cpu0Ist 00003000 INTL 20130117)

[ 0.296722] ACPI: SSDT 0x000000007ADD1C18 0003A5 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)

[ 0.299033] ACPI: Dynamic OEM Table Load:

[ 0.299167] ACPI: SSDT 0x0000000000000000 0003A5 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)

[ 0.299948] ACPI: SSDT 0x000000007ADD3E18 00015F (v01 PmRef ApIst 00003000 INTL 20130117)

[ 0.302314] ACPI: Dynamic OEM Table Load:

[ 0.302447] ACPI: SSDT 0x0000000000000000 00015F (v01 PmRef ApIst 00003000 INTL 20130117)

[ 0.302796] ACPI: SSDT 0x000000007ADDAE18 00008D (v01 PmRef ApCst 00003000 INTL 20130117)

[ 0.305108] ACPI: Dynamic OEM Table Load:

[ 0.305242] ACPI: SSDT 0x0000000000000000 00008D (v01 PmRef ApCst 00003000 INTL 20130117)

[ 0.307738] ACPI: Interpreter enabled

[ 0.307781] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131218/hwxface-580)

[ 0.307928] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-580)

[ 0.308081] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20131218/hwxface-580)

[ 0.308250] ACPI: (supports S0 S5 S0idle)

[ 0.308286] ACPI: Using IOAPIC for interrupt routing

[ 0.308600] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

[ 0.309429] ACPI: No dock devices found.

[ 0.313231] ACPI: Power Resource [USBC] (on)

[ 0.315840] ACPI: Power Resource [WWPR] (off)

[ 0.317168] ACPI: Power Resource [WWPR] (off)

[ 0.319385] ACPI: Power Resource [WWPR] (off)

[ 0.320655] ACPI: Power Resource [WWPR] (off)

[ 0.321762] ACPI: Power Resource [WWPR] (off)

[ 0.323167] ACPI: Power Resource [WWPR] (off)

[ 0.328398] ACPI: Power Resource [P33X] (off)

[ 0.340559] ACPI: \_SB_.PCI0.I2C1.BATC: is added to dep device list.

[ 0.341326] ACPI: Power Resource [CLK3] (on)

[ 0.341570] ACPI: Power Resource [CLK4] (off)

[ 0.348451] ACPI: Power Resource [CLK2] (on)

[ 0.350158] ACPI: Power Resource [CLK1] (on)

[ 0.351715] ACPI: Power Resource [CLK0] (on)

[ 0.351954] ACPI: Power Resource [CLK1] (on)

[ 0.352751] ACPI: Power Resource [P28X] (off)

[ 0.352976] ACPI: Power Resource [P18X] (off)

[ 0.364527] ACPI: Power Resource [ID3C] (on)

[ 0.376473] ACPI: Power Resource [P12X] (off)

[ 0.376730] ACPI: Power Resource [P28P] (off)

[ 0.376961] ACPI: Power Resource [P18P] (off)

[ 0.377191] ACPI: Power Resource [P19X] (off)

[ 0.377425] ACPI: Power Resource [P06X] (off)

[ 0.377782] ACPI: Power Resource [P28T] (off)

[ 0.378028] ACPI: Power Resource [P18D] (off)

[ 0.378256] ACPI: Power Resource [P18T] (off)

[ 0.378491] ACPI: Power Resource [P3P3] (off)

[ 0.378733] ACPI: Power Resource [P12T] (off)

[ 0.378967] ACPI: Power Resource [P28W] (off)

[ 0.379203] ACPI: Power Resource [P18W] (off)

[ 0.379431] ACPI: Power Resource [P12W] (off)

[ 0.379679] ACPI: Power Resource [P33W] (off)

[ 0.379923] ACPI: Power Resource [P4BW] (off)

[ 0.385416] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])

[ 0.385466] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]

[ 0.386074] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]

[ 0.386936] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge

[ 0.387505] PCI host bridge to bus 0000:00

[ 0.387545] pci_bus 0000:00: root bus resource [bus 00-ff]

[ 0.387592] pci_bus 0000:00: root bus resource [io 0x0000-0x006f]

[ 0.387642] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7]

[ 0.387693] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]

[ 0.387745] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]

[ 0.387796] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]

[ 0.387847] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff]

[ 0.387898] pci_bus 0000:00: root bus resource [mem 0x20000000-0x201fffff]

[ 0.387952] pci_bus 0000:00: root bus resource [mem 0x7cc00001-0x7ec00000]

[ 0.388003] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff]

[ 0.388067] pci 0000:00:00.0: [8086:2280] type 00 class 0x060000

[ 0.388531] pci 0000:00:02.0: [8086:22b0] type 00 class 0x030000

[ 0.388599] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x90ffffff 64bit]

[ 0.388649] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref]

[ 0.388694] pci 0000:00:02.0: reg 0x20: [io 0x1000-0x103f]

[ 0.389093] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000

[ 0.389160] pci 0000:00:03.0: reg 0x10: [mem 0x91000000-0x913fffff]

[ 0.389605] pci 0000:00:14.0: [8086:22b5] type 00 class 0x0c0330

[ 0.389678] pci 0000:00:14.0: reg 0x10: [mem 0x91a00000-0x91a0ffff 64bit]

[ 0.389827] pci 0000:00:14.0: PME# supported from D3hot D3cold

[ 0.390007] pci 0000:00:14.0: System wakeup disabled by ACPI

[ 0.390253] pci 0000:00:16.0: [8086:22b7] type 00 class 0x0c03fe

[ 0.390311] pci 0000:00:16.0: reg 0x10: [mem 0x91400000-0x915fffff]

[ 0.390449] pci 0000:00:16.0: PME# supported from D0 D3hot

[ 0.390795] pci 0000:00:1a.0: [8086:2298] type 00 class 0x108000

[ 0.390854] pci 0000:00:1a.0: reg 0x10: [mem 0x91900000-0x919fffff]

[ 0.390897] pci 0000:00:1a.0: reg 0x14: [mem 0x91800000-0x918fffff]

[ 0.391045] pci 0000:00:1a.0: PME# supported from D0 D3hot

[ 0.391421] pci 0000:00:1f.0: [8086:229c] type 00 class 0x060100

[ 0.391906] pci_bus 0000:00: on NUMA node 0

[ 0.392858] acpi_create_platform_device : pdevinfo.name = INT3496:00

[ 0.393630] acpi_create_platform_device : pdevinfo.name = 80860F14:00

[ 0.394151] acpi_create_platform_device : pdevinfo.name = INT33BB:01

[ 0.394769] acpi_create_platform_device : pdevinfo.name = 80862286:00

[ 0.395298] acpi_create_platform_device : pdevinfo.name = 808622C0:00

[ 0.395959] acpi_create_platform_device : pdevinfo.name = 8086228A:00

[ 0.396519] acpi_create_platform_device : pdevinfo.name = 8086228A:01

[ 0.397026] acpi_create_platform_device : pdevinfo.name = 8086228E:00

[ 0.397483] acpi_create_platform_device : pdevinfo.name = 8086228E:01

[ 0.397939] acpi_create_platform_device : pdevinfo.name = 8086228E:02

[ 0.398397] acpi_create_platform_device : pdevinfo.name = 808622C1:00

[ 0.399061] acpi_create_platform_device : pdevinfo.name = 808622C1:01

[ 0.399658] acpi_create_platform_device : pdevinfo.name = 808622C1:02

[ 0.400431] acpi_create_platform_device : pdevinfo.name = 808622C1:03

[ 0.401030] acpi_create_platform_device : pdevinfo.name = 808622C1:04

[ 0.401518] acpi_create_platform_device : pdevinfo.name = 808622C1:05

[ 0.402031] acpi_create_platform_device : pdevinfo.name = 808622C1:06

[ 0.402871] acpi_create_platform_device : pdevinfo.name = 808622A8:00

[ 0.403764] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.404623] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.405477] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.406346] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.407203] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.408055] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.408910] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.409763] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.

[ 0.410681] acpi_create_platform_device : pdevinfo.name = VIBR22A8:00

[ 0.411939] acpi_create_platform_device : pdevinfo.name = ITE8568:00

[ 0.412442] ACPI: Enabled 1 GPEs in block 00 to 3F

[ 0.413079] dw_dmac 80862286:00: DesignWare DMA Controller, 8 channels

[ 0.414592] dw_dmac 808622C0:00: DesignWare DMA Controller, 8 channels

[ 0.416543] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none

[ 0.416580] vgaarb: loaded

[ 0.416628] vgaarb: bridge control possible 0000:00:02.0

[ 0.417537] SCSI subsystem initialized

[ 0.417956] libata version 3.00 loaded.

[ 0.424702] ACPI: bus type USB registered

[ 0.424977] usbcore: registered new interface driver usbfs

[ 0.425122] usbcore: registered new interface driver hub

[ 0.425307] usbcore: registered new device driver usb

[ 0.426083] media: Linux media interface: v0.10

[ 0.426221] Linux video capture interface: v2.00

[ 0.426435] pps_core: LinuxPPS API ver. 1 registered

[ 0.426607] PTP clock support registered

[ 0.427593] Advanced Linux Sound Architecture Driver Initialized.

[ 0.427627] PCI: Using ACPI for IRQ routing

[ 0.430552] PCI: pci_cache_line_size set to 64 bytes

[ 0.430628] Expanded resource reserved due to conflict with PCI Bus 0000:00

[ 0.430664] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]

[ 0.430713] e820: reserve RAM buffer [mem 0x1f000000-0x1fffffff]

[ 0.430763] e820: reserve RAM buffer [mem 0x5c400000-0x5fffffff]

[ 0.430814] e820: reserve RAM buffer [mem 0x7a49e000-0x7bffffff]

[ 0.432183] amd_nb: Cannot enumerate AMD northbridges

[ 0.432256] Switched to clocksource refined-jiffies

[ 0.466983] pnp: PnP ACPI init

[ 0.467069] ACPI: bus type PNP registered

[ 0.467334] pnp 00:00: Plug and Play ACPI device, IDs INT0800 (active)

[ 0.467579] system 00:01: [io 0x0680-0x069f] has been reserved

[ 0.467617] system 00:01: [io 0x0400-0x047f] could not be reserved

[ 0.467667] system 00:01: [io 0x0500-0x05fe] has been reserved

[ 0.467723] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.468113] pnp 00:02: Plug and Play ACPI device, IDs PNP0501 (active)

[ 0.470732] pnp 00:03: Plug and Play ACPI device, IDs NXP1001 (active)

[ 0.471021] pnp 00:04: Plug and Play ACPI device, IDs SMO8501 (active)

[ 0.471447] pnp 00:05: Plug and Play ACPI device, IDs INTcf1c (active)

[ 0.471749] pnp 00:06: Plug and Play ACPI device, IDs INT33be (active)

[ 0.472571] pnp 00:07: Plug and Play ACPI device, IDs INT33fd (active)

[ 0.474605] system 00:08: [mem 0x91a35000-0x91a35fff] has been reserved

[ 0.474642] system 00:08: [mem 0x91a33000-0x91a33fff] has been reserved

[ 0.474693] system 00:08: [mem 0x91a22000-0x91a22fff] has been reserved

[ 0.474744] system 00:08: [mem 0x91a20000-0x91a20fff] has been reserved

[ 0.474795] system 00:08: [mem 0x91a1e000-0x91a1efff] has been reserved

[ 0.474846] system 00:08: [mem 0x91a1c000-0x91a1cfff] has been reserved

[ 0.474909] system 00:08: [mem 0x91a1a000-0x91a1afff] has been reserved

[ 0.474949] system 00:08: [mem 0x91a18000-0x91a18fff] has been reserved

[ 0.475000] system 00:08: [mem 0x91a31000-0x91a31fff] has been reserved

[ 0.475051] system 00:08: [mem 0x91a2f000-0x91a2ffff] has been reserved

[ 0.475102] system 00:08: [mem 0x91a2d000-0x91a2dfff] has been reserved

[ 0.475153] system 00:08: [mem 0x91a2b000-0x91a2bfff] has been reserved

[ 0.475207] system 00:08: [mem 0x91a29000-0x91a29fff] has been reserved

[ 0.475259] system 00:08: [mem 0x91a27000-0x91a27fff] has been reserved

[ 0.475314] system 00:08: [mem 0x91a25000-0x91a25fff] has been reserved

[ 0.475361] system 00:08: [mem 0x91a23000-0x91a23fff] has been reserved

[ 0.475416] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.476074] system 00:09: [mem 0xe0000000-0xefffffff] could not be reserved

[ 0.476108] system 00:09: [mem 0xfea00000-0xfeafffff] has been reserved

[ 0.476158] system 00:09: [mem 0xfed01000-0xfed01fff] has been reserved

[ 0.476209] system 00:09: [mem 0xfed03000-0xfed03fff] has been reserved

[ 0.476260] system 00:09: [mem 0xfed06000-0xfed06fff] has been reserved

[ 0.476312] system 00:09: [mem 0xfed08000-0xfed09fff] has been reserved

[ 0.476363] system 00:09: [mem 0xfed80000-0xfedbffff] has been reserved

[ 0.476414] system 00:09: [mem 0xfed1c000-0xfed1cfff] has been reserved

[ 0.476466] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved

[ 0.476521] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)

[ 0.477073] pnp 00:0a: Plug and Play ACPI device, IDs PNP0b00 (active)

[ 0.477396] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)

[ 0.478194] chv_gpio 00:0c: Cherryview GPIO GPO0 probed

[ 0.478233] chv_gpio 00:0c: Plug and Play ACPI device, IDs INT33ff (active)

[ 0.478915] chv_gpio 00:0d: Cherryview GPIO GPO1 probed

[ 0.479011] chv_gpio 00:0d: Plug and Play ACPI device, IDs INT33ff (active)

[ 0.479515] chv_gpio 00:0e: Cherryview GPIO GPO2 probed

[ 0.479554] chv_gpio 00:0e: Plug and Play ACPI device, IDs INT33ff (active)

[ 0.480280] chv_gpio 00:0f: Cherryview GPIO GPO3 probed

[ 0.480321] chv_gpio 00:0f: Plug and Play ACPI device, IDs INT33ff (active)

[ 0.481088] chv_gpio 00:10: Cherryview GPIO GPO4 probed

[ 0.481126] chv_gpio 00:10: Plug and Play ACPI device, IDs INT33ff (active)

[ 0.481785] pnp 00:11: Plug and Play ACPI device, IDs INTcfd9 PNP0c40 (active)

[ 0.482090] pnp 00:12: Plug and Play ACPI device, IDs INT33bd (active)

[ 0.482271] pnp: PnP ACPI: found 19 devices

[ 0.482304] ACPI: bus type PNP unregistered

[ 0.484081] register_psy_notifier

[ 0.488960] Switched to clocksource acpi_pm

[ 0.539827] pci_bus 0000:00: resource 4 [io 0x0000-0x006f]

[ 0.539864] pci_bus 0000:00: resource 5 [io 0x0078-0x0cf7]

[ 0.539914] pci_bus 0000:00: resource 6 [io 0x0d00-0xffff]

[ 0.540005] pci_bus 0000:00: resource 7 [mem 0x000a0000-0x000bffff]

[ 0.540039] pci_bus 0000:00: resource 8 [mem 0x000c0000-0x000dffff]

[ 0.540090] pci_bus 0000:00: resource 9 [mem 0x000e0000-0x000fffff]

[ 0.540142] pci_bus 0000:00: resource 10 [mem 0x20000000-0x201fffff]

[ 0.540193] pci_bus 0000:00: resource 11 [mem 0x7cc00001-0x7ec00000]

[ 0.540244] pci_bus 0000:00: resource 12 [mem 0x80000000-0xdfffffff]

[ 0.540370] NET: Registered protocol family 2

[ 0.540855] TCP established hash table entries: 32768 (order: 6, 262144 bytes)

[ 0.541048] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)

[ 0.541500] TCP: Hash tables configured (established 32768 bind 32768)

[ 0.541618] TCP: reno registered

[ 0.541665] UDP hash table entries: 2048 (order: 5, 196608 bytes)

[ 0.541786] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)

[ 0.542173] NET: Registered protocol family 1

[ 0.544717] intel_setup_crystal_cove_sd_regulators: sd_vsdio gpio 313

[ 0.544851] intel_setup_crystal_cove_sd_regulators: sd_vsdcard gpio 306

[ 0.544906] pci 0000:00:02.0: Boot video device

[ 0.547254] PCI: CLS 64 bytes, default 64

[ 0.552044] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.556447] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.561817] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.566696] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.570751] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.575249] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.575505] i2c_designware 808622C1:06: _SEM=0

[ 0.578045] intel_soc_pmic_i2c i2c-INT33FD:00: PMIC IRQ Base:456

[ 0.584224] crystal_cove_pwrsrc crystal_cove_pwrsrc: USB PORT ID: PERIPHERAL

[ 0.594574] gpio_vsdcard: 3300 mV normal

[ 0.595101] gpio_vsdio: 1800 <--> 3300 mV at 3300 mV normal

[ 0.599794] ACPI: \_SB_.PCI0.I2C1.BATC: Device_STA 0x00

[ 0.600247] Trying to unpack rootfs image as initramfs...

[ 0.804459] Freeing initrd memory: 5320K (ffff880000100000 - ffff880000632000)

[ 0.804502] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)

[ 0.804552] software IO TLB [mem 0x6fd3e000-0x73d3e000] (64MB) mapped at [ffff88006fd3e000-ffff880073d3dfff]

[ 0.805760] microcode: CPU0 sig=0x406c4, pf=0x1, revision=0x410

[ 0.805816] microcode: CPU1 sig=0x406c4, pf=0x1, revision=0x410

[ 0.805870] microcode: CPU2 sig=0x406c4, pf=0x1, revision=0x410

[ 0.805949] microcode: CPU3 sig=0x406c4, pf=0x1, revision=0x410

[ 0.806168] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba

[ 0.807985] Scanning for low memory corruption every 60 seconds

[ 0.809991] SSE version of gcm_enc/dec engaged.

[ 0.812268] sha1_ssse3: Using SSSE3 optimized SHA-1 implementation

[ 0.812417] sha256_ssse3: Using SSSE3 optimized SHA-256 implementation

[ 0.812684] sha512_ssse3: Using SSSE3 optimized SHA-512 implementation

[ 0.813209] AVX instructions are not detected.

[ 0.813527] vlv2_plat_clk vlv2_plat_clk: vlv2_plat_clk initialized

[ 0.813743] iwlwifi platform init

[ 0.815580] futex hash table entries: 1024 (order: 4, 65536 bytes)

[ 0.815641] Initialise system trusted keyring

[ 0.815730] audit: initializing netlink subsys (disabled)

[ 0.815801] audit: type=2000 audit(1532481698.787:1): initialized

[ 0.911280] VFS: Disk quotas dquot_6.5.2

[ 0.911649] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

[ 0.915816] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.917229] fuse init (API version 7.22)

[ 0.918378] Key type big_key registered

[ 0.918411] SELinux: Registering netfilter hooks

[ 0.923507] Key type asymmetric registered

[ 0.923546] Asymmetric key parser 'x509' registered

[ 0.924175] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)

[ 0.924208] io scheduler noop registered

[ 0.924258] io scheduler deadline registered

[ 0.924578] io scheduler cfq registered (default)

[ 0.928528] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[ 0.929120] pciehp: PCI Express Hot Plug Controller Driver version: 0.4

[ 0.929574] efifb: probing for efifb

[ 0.929661] efifb: framebuffer at 0x80000000, mapped to 0xffffc90004580000, using 4000k, total 4000k

[ 0.929692] efifb: mode is 800x1280x32, linelength=3200, pages=1

[ 0.929742] efifb: scrolling: redraw

[ 0.929795] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0

[ 0.930138] fb0: EFI VGA frame buffer device

[ 0.930547] intel_idle: MWAIT substates: 0x33000020

[ 0.930579] intel_idle: v0.4 model 0x4C

[ 0.930629] intel_idle: lapic_timer_reliable_states 0xffffffff

[ 0.932446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0

[ 0.932485] ACPI: Power Button [PWRB]

[ 0.933133] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1

[ 0.933168] ACPI: Power Button [PWRF]

[ 0.945533] ACPI: thermal control disabled

[ 0.949332] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[ 0.970004] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A

[ 0.974003] Found a Designware HSU

[ 0.974308] 8086228A:00: ttyHSU0 at MMIO 0x91a21000 (irq = 39, base_baud = 2764800) is a hsu_port0

[ 0.974685] Found a Designware HSU

[ 0.974883] 8086228A:01: ttyHSU1 at MMIO 0x91a1f000 (irq = 40, base_baud = 2764800) is a hsu_port1

[ 0.975844] hpet: number irqs doesn't agree with number of timers

[ 0.983375] Non-volatile memory driver v1.3

[ 0.983444] Linux agpgart interface v0.103

[ 0.983985] [drm] Initialized drm 1.1.0 20060810

[ 0.987752] [drm] Memory usable by graphics device = 2048M

[ 0.987792] checking generic (80000000 3e8000) vs hw (80000000 10000000)

[ 0.987838] fb: switching to inteldrmfb from EFI VGA

[ 0.991674] i915 0000:00:02.0: irq 134 for MSI/MSI-X

[ 0.991737] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).

[ 0.991767] [drm] Driver supports precise vblank timestamp query.

[ 0.996700] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem

[ 0.997838] DP intel_dsi_init panel_id 0x0

[ 0.999688] [drm] hdmi port 1, ddc_bus 5, hpd_pin 4

[ 1.805949] tsc: Refined TSC clocksource calibration: 1599.948 MHz

[ 1.806447] Switched to clocksource tsc

[ 1.894908] i2c i2c-11: normal 7 bit addr failed

[ 2.768883] i2c i2c-11: normal 7 bit addr failed

[ 2.779261] [drm] hdmi port 3, ddc_bus 3, hpd_pin 6

[ 3.673853] i2c i2c-9: normal 7 bit addr failed

[ 4.547824] i2c i2c-9: normal 7 bit addr failed

[ 4.560392] i915 0000:00:02.0: Direct firmware load failed with error -2

[ 4.565997] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off

[ 4.568000] i915 0000:00:02.0: Falling back to user helper

[ 4.574219] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device

[ 4.574254] i915 0000:00:02.0: registered panic notifier

[ 4.586747] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)

[ 4.588336] acpi device:28: registered as cooling_device4

[ 4.589478] acpi device:29: registered as cooling_device5

[ 4.590642] acpi device:2a: registered as cooling_device6

[ 4.591804] acpi device:2b: registered as cooling_device7

[ 4.592880] acpi device:2c: registered as cooling_device8

[ 4.594042] acpi device:2d: registered as cooling_device9

[ 4.595109] acpi device:2e: registered as cooling_device10

[ 4.596198] acpi device:2f: registered as cooling_device11

[ 4.596535] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input2

[ 4.596745] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0

[ 4.605371] brd: module loaded

[ 4.609340] loop: module loaded

[ 4.609875] zram: Created 1 device(s) ...

[ 4.610584] mei_txe 0000:00:1a.0: irq 135 for MSI/MSI-X

[ 4.617864] tun: Universal TUN/TAP device driver, 1.6

[ 4.618118] PPP generic driver version 2.4.2

[ 4.618411] PPP BSD Compression module registered

[ 4.618444] PPP Deflate Compression module registered

[ 4.618507] PPP MPPE Compression module registered

[ 4.618547] NET: Registered protocol family 24

[ 4.618738] usbcore: registered new interface driver catc

[ 4.618903] usbcore: registered new interface driver kaweth

[ 4.618936] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver

[ 4.619110] usbcore: registered new interface driver pegasus

[ 4.619273] usbcore: registered new interface driver rtl8150

[ 4.619422] usbcore: registered new interface driver r8152

[ 4.619586] usbcore: registered new interface driver asix

[ 4.619736] usbcore: registered new interface driver ax88179_178a

[ 4.619902] usbcore: registered new interface driver cdc_ether

[ 4.620054] usbcore: registered new interface driver cdc_eem

[ 4.620200] usbcore: registered new interface driver dm9601

[ 4.620353] usbcore: registered new interface driver smsc75xx

[ 4.620511] usbcore: registered new interface driver smsc95xx

[ 4.620663] usbcore: registered new interface driver net1080

[ 4.620971] usbcore: registered new interface driver cdc_subset

[ 4.621132] usbcore: registered new interface driver zaurus

[ 4.621284] usbcore: registered new interface driver MOSCHIP usb-ethernet driver

[ 4.621456] usbcore: registered new interface driver ipheth

[ 4.621619] usbcore: registered new interface driver cdc_ncm

[ 4.622445] EM:OEM1 table found, size=64

[ 4.622477] cht_otg_probe : usb none_compliance mode selected

[ 4.622739] usb_phy_gen_xceiv.1 supply vcc not found, using dummy regulator

[ 4.630626] usb_phy_gen_xceiv usb_phy_gen_xceiv.1: No RESET GPIO is available

[ 4.630661] usb_phy_gen_xceiv usb_phy_gen_xceiv.1: No CS GPIO is available

[ 4.630945] dwc3_probe+++++++

[ 4.634413] dwc3_core_soft_reset+++++++++

[ 4.839084] dwc3_core_num_eps(): found 16 IN and 2044295888 OUT endpoints

[ 4.846714] dwc3_probe(): dwc dr mode 2

[ 4.851566] dwc3 dwc3.0.auto: dwc3_suspend_common

[ 4.856885] dwc3_suspend_common(): Host Mode

[ 4.861713] dwc3_probe-----------

[ 4.866155] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 4.866201] ehci-pci: EHCI PCI platform driver

[ 4.867322] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 4.867366] uhci_hcd: USB Universal Host Controller Interface driver

[ 4.867978] xhci_hcd 0000:00:14.0: xHCI Host Controller

[ 4.868326] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1

[ 4.868487] xhci_hcd 0000:00:14.0: ssic_device_present[1] ssic_port_number[5]

[ 4.876532] no xhci or phy_mux_regs

[ 4.881658] intel-cht-otg intel-cht-otg.0: cht_otg_set_host id is 1

[ 4.965162] dwc3_pci_suspend_common +++++++++

[ 4.970091] dwc3_pci_suspend_common pci_disable_device....

[ 5.891033] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported

[ 5.891139] xhci_hcd 0000:00:14.0: irq 136 for MSI/MSI-X

[ 5.891400] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 5.891434] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 5.891488] usb usb1: Product: xHCI Host Controller

[ 5.891539] usb usb1: Manufacturer: Linux 3.14.79-x86_64-svn6727 xhci_hcd

[ 5.891590] usb usb1: SerialNumber: 0000:00:14.0

[ 5.892924] hub 1-0:1.0: USB hub found

[ 5.892998] hub 1-0:1.0: 7 ports detected

[ 5.895177] xhci_hcd 0000:00:14.0: xHCI Host Controller

[ 5.895601] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2

[ 5.895804] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003

[ 5.895839] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 5.895889] usb usb2: Product: xHCI Host Controller

[ 5.895941] usb usb2: Manufacturer: Linux 3.14.79-x86_64-svn6727 xhci_hcd

[ 5.895991] usb usb2: SerialNumber: 0000:00:14.0

[ 5.897124] hub 2-0:1.0: USB hub found

[ 5.897194] hub 2-0:1.0: 6 ports detected

[ 5.901433] usbcore: registered new interface driver cdc_acm

[ 5.901469] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 5.901814] usbcore: registered new interface driver usb-storage

[ 5.902111] usbcore: registered new interface driver ums-realtek

[ 5.902686] usbcore: registered new interface driver usbserial

[ 5.903038] usbcore: registered new interface driver usbserial_generic

[ 5.903299] usbserial: USB Serial support registered for generic

[ 5.903532] usbcore: registered new interface driver ark3116

[ 5.903810] usbserial: USB Serial support registered for ark3116

[ 5.904085] usbcore: registered new interface driver belkin_sa

[ 5.904375] usbserial: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter

[ 5.904638] usbcore: registered new interface driver ch341

[ 5.904859] usbserial: USB Serial support registered for ch341-uart

[ 5.905103] usbcore: registered new interface driver cp210x

[ 5.905380] usbserial: USB Serial support registered for cp210x

[ 5.905672] usbcore: registered new interface driver digi_acceleport

[ 5.906051] usbserial: USB Serial support registered for Digi 2 port USB adapter

[ 5.906319] usbserial: USB Serial support registered for Digi 4 port USB adapter

[ 5.906571] usbcore: registered new interface driver f81232

[ 5.907000] usbserial: USB Serial support registered for f81232

[ 5.907332] usbcore: registered new interface driver ftdi_sio

[ 5.907589] usbserial: USB Serial support registered for FTDI USB Serial Device

[ 5.907884] usbcore: registered new interface driver mct_u232

[ 5.908167] usbserial: USB Serial support registered for MCT U232

[ 5.908465] usbcore: registered new interface driver mos7720

[ 5.908743] usbserial: USB Serial support registered for Moschip 2 port adapter

[ 5.909016] usbcore: registered new interface driver mos7840

[ 5.909246] usbserial: USB Serial support registered for Moschip 7840/7820 USB Serial Driver

[ 5.909504] usbcore: registered new interface driver option

[ 5.909797] usbserial: USB Serial support registered for GSM modem (1-port)

[ 5.910195] usbcore: registered new interface driver oti6858

[ 5.910449] usbserial: USB Serial support registered for oti6858

[ 5.910740] usbcore: registered new interface driver pl2303

[ 5.910992] usbserial: USB Serial support registered for pl2303

[ 5.911257] usbcore: registered new interface driver spcp8x5

[ 5.911543] usbserial: USB Serial support registered for SPCP8x5

[ 5.911828] usbcore: registered new interface driver ssu100

[ 5.912093] usbserial: USB Serial support registered for Quatech SSU-100 USB to Serial Driver

[ 5.912377] usbcore: registered new interface driver ti_usb_3410_5052

[ 5.912541] usbserial: USB Serial support registered for TI USB 3410 1 port adapter

[ 5.912794] usbserial: USB Serial support registered for TI USB 5052 2 port adapter

[ 5.912979] usbcore: registered new interface driver whiteheat

[ 5.913146] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)

[ 5.913403] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT

[ 5.913632] usbcore: registered new interface driver keyspan_pda

[ 5.913890] usbserial: USB Serial support registered for Keyspan PDA

[ 5.914165] usbserial: USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)

[ 5.914466] usbcore: registered new interface driver usb_ehset_test

[ 5.915588] mousedev: PS/2 mouse device common for all mice

[ 5.917059] usbcore: registered new interface driver xpad

[ 5.917355] usbcore: registered new interface driver usb_acecad

[ 5.917739] usbcore: registered new interface driver aiptek

[ 5.918041] usbcore: registered new interface driver gtco

[ 5.918290] usbcore: registered new interface driver hanwang

[ 5.918547] usbcore: registered new interface driver kbtab

[ 5.919061] usbcore: registered new interface driver wacom

[ 5.919095] <<-GTP-INFO->> GTP driver installing....

[ 5.919685] <<-GTP-INFO->> GTP Driver Version: V2.4.0.1<2016/10/26>

[ 5.919717] <<-GTP-INFO->> GTP Driver Built@07:14:09, Jun 28 2018

[ 5.919790] <<-GTP-INFO->> GTP I2C Address: 0x5d

[ 5.919889] <<-GTP-INFO->> Guitar reset

[ 6.006017] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -121!

[ 6.009777] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -121! Process reset.

[ 6.009808] <<-GTP-INFO->> Guitar reset

[ 6.083428] <<-GTP-ERROR->> GTP i2c test failed time 1.

[ 6.094861] port4: status 0101, change 0000, 12 Mb/s

[ 6.100598] hub 1-0:1.0: hub_port_connect+++++++++++++

[ 6.106411] hub port 0x101

[ 6.109796] hub 1-0:1.0: hub_port_reset():++++++++++++

[ 6.115585] hub 1-0:1.0: hub_port_reset(): SW Reset Port

[ 6.121567] <<-GTP-INFO->> IC Version: 928_1060

[ 6.121600] <<-GTP-INFO->> goodix_ts_probe() : firmware version: 4192

[ 6.121600]

[ 6.126981] <<-GTP-INFO->> Sensor_ID: 0

[ 6.127021] <<-GTP-INFO->> Config group0 used,length: 186

[ 6.128945] <<-GTP-INFO->> Driver send config.

[ 6.140112] <<-GTP-INFO->> X_MAX: 1281, Y_MAX: 801, TRIGGER: 0x00

[ 6.151143] <<-GTP-INFO->> create proc entry gt9xx_config success

[ 6.151185] <<-GTP-INFO->> Esd started

[ 6.151907] input: goodix-ts as /devices/virtual/input/input3

[ 6.152228] <<-GTP-ERROR->> Request IRQ failed!ERRNO:1.

[ 6.152276] <<-GTP-INFO->> GTP works in polling mode.

[ 6.152315] <<-GTP-INFO->> Applied memory size:2562.

[ 6.152367] <<-GTP-INFO->> I2C function: without pre and end cmd!

[ 6.152431] <<-GTP-INFO->> Create proc entry success!

[ 6.154595] [egalax_i2c]: Driver init done!

[ 6.156919] PANEL_ID_1=1

[ 6.156954] PANEL_ID_2=1

[ 6.157006] PANEL_ID_3=1

[ 6.157059] PANEL_ID_4=1

[ 6.157111] >>>> get_panel_id : PANEL_ID_NUM=0xf

[ 6.158452] rtc_cmos 00:0a: rtc core: registered rtc_cmos as rtc0

[ 6.158551] rtc_cmos 00:0a: alarms up to one month, y3k, 242 bytes nvram

[ 6.159020] i2c /dev entries driver

[ 6.164798] usbcore: registered new interface driver uvcvideo

[ 6.164834] USB Video Class driver (1.1.1)

[ 6.166055] can't get ec bypass battery jumper status

[ 6.171826] can't get ec bypass battery jumper status

[ 6.177559] can't get ec bypass battery jumper status

[ 6.183246] can't get ec bypass battery jumper status

[ 6.188930] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.195486] can't get ec bypass battery jumper status

[ 6.201166] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.207721] can't get ec bypass battery jumper status

[ 6.213402] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.219957] can't get ec bypass battery jumper status

[ 6.225637] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.232201] can't get ec bypass battery jumper status

[ 6.237886] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.244440] can't get ec bypass battery jumper status

[ 6.250124] can't get ec bypass battery jumper status

[ 6.255806] can't get ec bypass battery jumper status

[ 6.261486] can't get ec bypass battery jumper status

[ 6.267165] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.273877] usb 1-4: new high-speed USB device number 2 using xhci_hcd

[ 6.274169] hub 1-0:1.0: hub_port_reset():++++++++++++

[ 6.279979] hub 1-0:1.0: hub_port_reset(): SW Reset Port

[ 6.280054] can't get ec bypass battery jumper status

[ 6.280056] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280060] thermal thermal_zone0: failed to read out thermal zone 0

[ 6.280187] can't get ec bypass battery jumper status

[ 6.280199] can't get ec bypass battery jumper status

[ 6.280200] can't get ec bypass battery jumper status

[ 6.280204] can't get ec bypass battery jumper status

[ 6.280207] can't get ec bypass battery jumper status

[ 6.280208] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280209] can't get ec bypass battery jumper status

[ 6.280210] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280211] can't get ec bypass battery jumper status

[ 6.280212] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280213] can't get ec bypass battery jumper status

[ 6.280214] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280215] can't get ec bypass battery jumper status

[ 6.280216] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280217] can't get ec bypass battery jumper status

[ 6.280220] can't get ec bypass battery jumper status

[ 6.280223] can't get ec bypass battery jumper status

[ 6.280225] can't get ec bypass battery jumper status

[ 6.280226] ec_it8568_bus_read_word : ec_it8565_di_ptr is null

[ 6.280772] ec_it8568_i2c_probe()

[ 6.282810] ec_it8568_i2c_probe : EC BOARD ID - 0xa0

[ 6.285764] ec_it8568_i2c_probe : EC VERSION - 0x0.0x21.0x38

[ 6.286269] ec_it8568_i2c_probe : EC Vibrator is enabled

[ 6.298996] intel_powerclamp: Intel powerclamp does not run on family 6 model 76

[ 6.300135] pmic_thermal crystal_cove_thermal: No thermal data initialized!!

[ 6.300247] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11

[ 6.300365] iTCO_wdt: Found a Cherry Trail SoC TCO device (Version=3, TCOBASE=0x0460)

[ 6.300785] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)

[ 6.301305] device-mapper: uevent: version 1.0.3

[ 6.301661] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com

[ 6.301849] Intel P-state driver initializing.

[ 6.301876] Intel pstate controlling: cpu 0

[ 6.305335] Intel pstate controlling: cpu 1

[ 6.305793] Intel pstate controlling: cpu 2

[ 6.306115] Intel pstate controlling: cpu 3

[ 6.306874] sdhci: Secure Digital Host Controller Interface driver

[ 6.306877] sdhci: Copyright(c) Pierre Ossman

[ 6.308261] mmc0: no vqmmc regulator found

[ 6.308272] mmc0: no vmmc regulator found

[ 6.309034] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA

[ 6.353110] mmc1: SDHCI controller on ACPI [INT33BB:01] using ADMA

[ 6.358392] ------------[ cut here ]------------

[ 6.358401] WARNING: CPU: 0 PID: 1 at /media/ethanma/workspace/d42/trunk_nougat_70/kernel/cht/fs/sysfs/dir.c:52 sysfs_warn_dup+0x86/0xa0()

[ 6.358402] sysfs: cannot create duplicate filename '/class/switch'

[ 6.358404] Modules linked in:

[ 6.358407] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.79-x86_64-svn6727 #131

[ 6.358408] Hardware name: Insyde CherryTrail/Type2 - Board Product Name, BIOS D420V101(D420-10103) 05/24/2018

[ 6.358414] 0000000000000000 ffff880179d97cd0 ffffffff81ab5e56 ffff880179d97d18

[ 6.358417] 0000000000000009 ffff880179d97d08 ffffffff8108b89d ffff8801004c3000

[ 6.358419] ffff8801004c3000 ffff880179c95438 ffffffff81fe7fb8 0000000000000000

[ 6.358420] Call Trace:

[ 6.358428] [<ffffffff81ab5e56>] dump_stack+0x67/0x90

[ 6.358433] [<ffffffff8108b89d>] warn_slowpath_common+0x7d/0xa0

[ 6.358435] [<ffffffff8108b90c>] warn_slowpath_fmt+0x4c/0x50

[ 6.358437] [<ffffffff8123b946>] sysfs_warn_dup+0x86/0xa0

[ 6.358439] [<ffffffff8123b9ed>] sysfs_create_dir_ns+0x8d/0xa0

[ 6.358444] [<ffffffff81391056>] kobject_add_internal+0xc6/0x450

[ 6.358446] [<ffffffff81390bce>] ? kobject_set_name+0x3e/0x40

[ 6.358449] [<ffffffff81391480>] kset_register+0x20/0x50

[ 6.358453] [<ffffffff815a1bd1>] __class_register+0xe1/0x260

[ 6.358456] [<ffffffff815a1da1>] __class_create+0x51/0x90

[ 6.358460] [<ffffffff825840f8>] ? leds_init+0x3c/0x3c

[ 6.358465] [<ffffffff8181e5ce>] create_switch_class.part.1+0x1e/0x40

[ 6.358468] [<ffffffff8258410d>] switch_class_init+0x15/0x17

[ 6.358472] [<ffffffff81000422>] do_one_initcall+0xf2/0x1b0

[ 6.358476] [<ffffffff810adc28>] ? parse_args+0x158/0x490

[ 6.358480] [<ffffffff8253df56>] kernel_init_freeable+0x195/0x21d

[ 6.358483] [<ffffffff81aafaa0>] ? rest_init+0x90/0x90

[ 6.358485] [<ffffffff81aafaae>] kernel_init+0xe/0xf0

[ 6.358488] [<ffffffff81acb008>] ret_from_fork+0x58/0x90

[ 6.358490] [<ffffffff81aafaa0>] ? rest_init+0x90/0x90

[ 6.358504] ---[ end trace a26738ab24f91435 ]---

[ 6.358506] ------------[ cut here ]------------

[ 6.358508] WARNING: CPU: 0 PID: 1 at /media/ethanma/workspace/d42/trunk_nougat_70/kernel/cht/lib/kobject.c:240 kobject_add_internal+0x3d4/0x450()

[ 6.358510] kobject_add_internal failed for switch with -EEXIST, don't try to register things with the same name in the same directory.

[ 6.358511] Modules linked in:

[ 6.358513] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.14.79-x86_64-svn6727 #131

[ 6.358514] Hardware name: Insyde CherryTrail/Type2 - Board Product Name, BIOS D420V101(D420-10103) 05/24/2018

[ 6.358516] 0000000000000000 ffff880179d97d20 ffffffff81ab5e56 ffff880179d97d68

[ 6.358519] 0000000000000009 ffff880179d97d58 ffffffff8108b89d ffff880179976c28

[ 6.358522] 00000000ffffffef ffff880179e42828 ffffffff81fe7fb8 0000000000000000

[ 6.358522] Call Trace:

[ 6.358525] [<ffffffff81ab5e56>] dump_stack+0x67/0x90

[ 6.358527] [<ffffffff8108b89d>] warn_slowpath_common+0x7d/0xa0

[ 6.358529] [<ffffffff8108b90c>] warn_slowpath_fmt+0x4c/0x50

[ 6.358532] [<ffffffff81391364>] kobject_add_internal+0x3d4/0x450

[ 6.358534] [<ffffffff81390bce>] ? kobject_set_name+0x3e/0x40

[ 6.358536] [<ffffffff81391480>] kset_register+0x20/0x50

[ 6.358538] [<ffffffff815a1bd1>] __class_register+0xe1/0x260

[ 6.358541] [<ffffffff815a1da1>] __class_create+0x51/0x90

[ 6.358543] [<ffffffff825840f8>] ? leds_init+0x3c/0x3c

[ 6.358545] [<ffffffff8181e5ce>] create_switch_class.part.1+0x1e/0x40

[ 6.358547] [<ffffffff8258410d>] switch_class_init+0x15/0x17

[ 6.358550] [<ffffffff81000422>] do_one_initcall+0xf2/0x1b0

[ 6.358552] [<ffffffff810adc28>] ? parse_args+0x158/0x490

[ 6.358554] [<ffffffff8253df56>] kernel_init_freeable+0x195/0x21d

[ 6.358556] [<ffffffff81aafaa0>] ? rest_init+0x90/0x90

[ 6.358558] [<ffffffff81aafaae>] kernel_init+0xe/0xf0

[ 6.358560] [<ffffffff81acb008>] ret_from_fork+0x58/0x90

[ 6.358562] [<ffffffff81aafaa0>] ? rest_init+0x90/0x90

[ 6.358564] ---[ end trace a26738ab24f91436 ]---

[ 6.359494] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)

[ 6.359499] EFI Variables Facility v0.08 2004-May-17

[ 6.470827] hidraw: raw HID events driver (C) Jiri Kosina

[ 6.486732] usbcore: registered new interface driver usbhid

[ 6.486735] usbhid: USB HID core driver

[ 6.488481] ashmem: initialized

[ 6.489062] logger: created 256K log 'log_main'

[ 6.489558] logger: created 256K log 'log_events'

[ 6.490094] logger: created 256K log 'log_radio'

[ 6.490577] logger: created 256K log 'log_system'

[ 6.494515] intel_warn_int: initialized. Interrupt=SCI GPE 0x0e

[ 6.494516] intel_tasks_dumper: intel_tasks_dumper_init: Register tasks dumper

[ 6.502496] intel_rapl: RAPL domain uncore detection failed

[ 6.502504] intel_rapl: RAPL domain dram detection failed

[ 6.568727] >>>> ext_csd[EXT_CSD_DEVICE_LIFTE_TIME_EST_TYP_A] = 0x1

[ 6.568728] >>>> ext_csd[EXT_CSD_DEVICE_LIFTE_TIME_EST_TYP_B] = 0x1

[ 6.769274] mmc0: new HS200 MMC card at address 0001

[ 6.770609] mmcblk0: mmc0:0001 DF4064 58.2 GiB

[ 6.770798] mmcblk0boot0: mmc0:0001 DF4064 partition 1 4.00 MiB

[ 6.770955] mmcblk0boot1: mmc0:0001 DF4064 partition 2 4.00 MiB

[ 6.771111] mmcblk0rpmb: mmc0:0001 DF4064 partition 3 4.00 MiB

[ 6.794038] ov5693 i2c-INT33BE:00: ov5693_probe +++++++++

[ 6.794102] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_I2CAddr

[ 6.794576] USB OTG is client mode

[ 6.794982] crystal_cove_pwrsrc crystal_cove_pwrsrc: VBUS attach event

[ 6.803254] crystal_cove_pwrsrc crystal_cove_pwrsrc: sent USB_EVENT_VBUS

[ 6.803257] intel-cht-otg intel-cht-otg.0: USB_EVENT_VBUS vbus valid

[ 6.803261] dwc3 dwc3.0.auto: DWC3 OTG Notify USB_EVENT_VBUS

[ 6.804458] crystal_cove_pwrsrc crystal_cove_pwrsrc: USB PORT ID: HOST

[ 6.804461] intel-cht-otg intel-cht-otg.0: [extcon notification]: USB-Host: connected

[ 6.806797] dwc3_pci_resume_common +++++++

[ 6.806798] dwc3_pci_resume_common pci_enable_device....

[ 6.806964] dwc3 dwc3.0.auto: dwc3_resume_common

[ 6.809118] dwc3_resume_common(): Host Mode

[ 6.871684] Found INT33BE

[ 6.875231] ov5693 i2c-INT33BE:00: gmin: initializing atomisp module subdev data.PMIC ID 4

[ 6.875272] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_CamClk

[ 6.875400] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12

[ 6.883430] Found INT33BE

[ 6.886491] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_ClkSrc

[ 6.894595] Found INT33BE

[ 6.897788] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_CsiPort

[ 6.906029] Found INT33BE

[ 6.906592] mmcblk0boot1: unknown partition table

[ 6.909170] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_CsiLanes

[ 6.917472] Found INT33BE

[ 6.917777] mmcblk0boot0: unknown partition table

[ 6.918869] usb 1-4: New USB device found, idVendor=05e3, idProduct=0610

[ 6.918874] usb 1-4: New USB device strings: Mfr=0, Product=1, SerialNumber=0

[ 6.918878] usb 1-4: Product: USB2.0 Hub

[ 6.919968] hub 1-4:1.0: USB hub found

[ 6.920269] hub 1-4:1.0: 4 ports detected

[ 6.921003] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo1_1p8v

[ 6.923009] xhci_hcd 0000:00:14.0: udev[1-4]: Check if need unblock ssic runtime, portnum[4] ssic_runtime_blocked[0]

[ 6.923077] hub 1-0:1.0: hub_port_connect------------------

[ 6.923130] port1: status 0203, change 0000, 5.0 Gb/s

[ 6.923135] hub 2-0:1.0: hub_port_connect+++++++++++++

[ 6.923137] hub port 0x203

[ 6.923204] hub 2-0:1.0: hub_port_reset():++++++++++++

[ 6.923207] hub 2-0:1.0: hub_port_reset(): USB3 SW Reset

[ 6.923240] hub 2-0:1.0: hub_port_reset(): SW Reset Port

[ 6.980044] Found INT33BE

[ 6.983180] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo1_sel_reg

[ 6.992007] Found INT33BE

[ 6.995135] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo1_ctrl_shift

[ 7.004253] Found INT33BE

[ 7.007386] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo2_1p8v

[ 7.015921] Found INT33BE

[ 7.019052] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo2_sel_reg

[ 7.026214] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd

[ 7.027894] Found INT33BE

[ 7.031023] acpi INT33BE:00: gmin_get_config_var() dev_name INT33BE:00_eldo2_ctrl_shift

[ 7.040131] Found INT33BE

[ 7.040685] usb 2-1: New USB device found, idVendor=0781, idProduct=5581

[ 7.040698] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[ 7.040707] usb 2-1: Product: Ultra

[ 7.040715] usb 2-1: Manufacturer: SanDisk

[ 7.040723] usb 2-1: SerialNumber: 4C531001400925120015

[ 7.043535] ov5693 i2c-INT33BE:00: ov5693_probe(): set ov5693 config

[ 7.043573] ov5693 i2c-INT33BE:00: ov5693_s_config(): +++++++++

[ 7.043644] ov5693 i2c-INT33BE:00: ov5693 Power On v2p8

[ 7.044477] ov5693 i2c-INT33BE:00: ov5693 Power On v1p8

[ 7.045080] xhci_hcd 0000:00:14.0: SS port 8 goes into inactive

[ 7.045221] ov5693 i2c-INT33BE:00: ov5693 Power On v1p2

[ 7.051800] xhci_hcd 0000:00:14.0: TRB error code 4, halted endpoint index = 0

[ 7.060061] usb 2-1: Disable of device-initiated U2 failed.

[ 7.066389] usb-storage 2-1:1.0: USB Mass Storage device detected

[ 7.066738] scsi0 : usb-storage 2-1:1.0

[ 7.067916] xhci_hcd 0000:00:14.0: udev[2-1]: Check if need unblock ssic runtime, portnum[1] ssic_runtime_blocked[0]

[ 7.079837] hub 2-0:1.0: hub_port_connect------------------

[ 7.086176] port1: do warm reset

[ 7.089932] hub 2-0:1.0: hub_port_reset():++++++++++++

[ 7.095707] hub 2-0:1.0: hub_port_reset(): SW Reset Port

[ 7.102746] ov5693 i2c-INT33BE:00: camera pdata: port: 0 lanes: 2 order: 00000002

[ 7.102777] ov5693 i2c-INT33BE:00: ov5693_detect(): +++++++++

[ 7.104755] ov5693 id: 0x5690

[ 7.202915] port1: status 02c0, change 0041, 5.0 Gb/s

[ 7.208737] hub 2-0:1.0: hub_port_connect+++++++++++++

[ 7.214549] hub 2-0:1.0: hub_port_connect usb is SanDisk port state 0x2c0

[ 7.222211] usb 2-1: USB disconnect, device number 2

[ 7.224300] xhci_hcd 0000:00:14.0: udev[2-1]: Check if need block ssic runtime, portnum[1] ssic_runtime_blocked[0]

[ 7.236645] check Port status and changes

[ 7.241373] Verify the debounce is stable

[ 7.349814] hub port 0x2a0

[ 7.353103] hub 2-0:1.0: hub_port_connect usb disconnected

[ 7.359702] port1: status 0101, change 0000, 12 Mb/s

[ 7.365743] hub 1-4:1.0: hub_port_connect+++++++++++++

[ 7.371556] hub port 0x101

[ 7.374890] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.380696] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 7.449066] usb 1-4.1: new high-speed USB device number 3 using xhci_hcd

[ 7.449262] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.455106] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 7.484769] ov5693 i2c-INT33BE:00: register atomisp i2c module type 1

[ 7.484813] ov5693 i2c-INT33BE:00: ov5693_probe(): register ov5693 successfull

[ 7.484864] ov5693 i2c-INT33BE:00: ov5693_probe -----------------

[ 7.487216] usbcore: registered new interface driver snd-usb-audio

[ 7.489597] dbg: rt5670_i2c_probe line 3787

[ 7.492174] snd_intel_sst: sst_platform_get_resources_edk

[ 7.498106] snd_intel_sst: LPE base: 0x91600000 size:0x200000snd_intel_sst: IRAM base: 0x916c0000

[ 7.508309] snd_intel_sst: DRAM base: 0x91700000snd_intel_sst: SHIM base: 0x91740000

[ 7.517169] snd_intel_sst: Mailbox base: 0x91744000snd_intel_sst: DDR base: 0x20000000

[ 7.526663] snd_intel_sst: Enter: sst_audio_platform_init

[ 7.526949] snd_intel_sst: audio:set_cht_platform_config

[ 7.527406] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.527453] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.527499] snd_intel_sst: >>>> sst_request_firmware_async() : board_name=Type2 - Board Product Name

[ 7.527544] snd_intel_sst: Registering machine device cht_rt5672

[ 7.527730] platform sst-platform: Direct firmware load failed with error -2

[ 7.531845] snd_intel_sst: Requesting FW fw_sst_22a8.bin now...

[ 7.531921] intel_sst_acpi 808622A8:00: Direct firmware load failed with error -2

[ 7.531924] intel_sst_acpi 808622A8:00: Falling back to user helper

[ 7.537946] u32 classifier

[ 7.537947] Actions configured

[ 7.537951] Netfilter messages via NETLINK v0.30.

[ 7.537998] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)

[ 7.538413] ctnetlink v0.93: registering with nfnetlink.

[ 7.539037] xt_time: kernel timezone is -0000

[ 7.558828] platform sst-platform: Falling back to user helper

[ 7.565848] usb 1-4.1: device v0bda p0823 is not supported

[ 7.572373] usb 1-4.1: New USB device found, idVendor=0bda, idProduct=0823

[ 7.572406] usb 1-4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[ 7.572426] TCP: cubic registered

[ 7.572428] Initializing XFRM netlink socket

[ 7.572586] usb 1-4.1: Product: 802.11ac WLAN Adapter

[ 7.572623] usb 1-4.1: Manufacturer: Realtek

[ 7.572668] usb 1-4.1: SerialNumber: 00e04c000001

[ 7.574503] NET: Registered protocol family 10

[ 7.576547] xhci_hcd 0000:00:14.0: udev[1-4.1]: Check if need unblock ssic runtime, portnum[1] ssic_runtime_blocked[0]

[ 7.589022] hub 1-4:1.0: hub_port_connect------------------

[ 7.595569] mip6: Mobile IPv6

[ 7.596011] port3: status 0101, change 0000, 12 Mb/s

[ 7.602338] hub 1-4:1.0: hub_port_connect+++++++++++++

[ 7.608345] hub port 0x101

[ 7.611978] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.617989] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 7.624608] sit: IPv6 over IPv4 tunneling driver

[ 7.625975] NET: Registered protocol family 17

[ 7.626029] NET: Registered protocol family 15

[ 7.626078] l2tp_core: L2TP core driver, V2.0

[ 7.626114] l2tp_ppp: PPPoL2TP kernel driver, V2.0

[ 7.626189] Key type dns_resolver registered

[ 7.628296] Loading compiled-in X.509 certificates

[ 7.630027] Loaded X.509 cert 'Magrathea: Glacier signing key: 5d18b4ebfa4c3e0ebaafbd93ef3ef97bba2bd493'

[ 7.630079] registered taskstats version 1

[ 7.631389] Key type encrypted registered

[ 7.631797] gpio_vsdio: disabling

[ 7.631829] gpio_vsdcard: disabling

[ 7.631879] regulator-dummy: disabling

[ 7.632264] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.632302] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.632361] Magic number: 10:809:357

[ 7.632443] input event3: hash matches

[ 7.633013] console [netcon0] enabled

[ 7.633045] netconsole: network logging started

[ 7.633368] input: gpio-keys as /devices/platform/gpio-keys.1.auto/input/input4

[ 7.633589] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.633626] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.634132] intel_mid_vibra: >>>> intel_mid_plat_vibra_probe : board_name[Type2 - Board Product Name]

[ 7.634646] rtc_cmos 00:0a: setting system clock to 2018-07-25 01:21:46 UTC (1532481706)

[ 7.634894] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found

[ 7.634924] EDD information not available.

[ 7.635476] had: Vidya: Enter alsa_card_intelhad_init

[ 7.641170] had: ******** HAD DRIVER loading.. Ver: 0.01.003

[ 7.642239] [drm] mid_hdmi_audio_register: Scheduling HDMI audio work queue

[ 7.642376] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.642417] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.642707] snd_byt_driver_init: BYT-CR-RT5640 Machine driver registered.

[ 7.642885] snd_byt_driver_init: BYT-CR-RT5651 Machine driver registered.

[ 7.642992] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 7.651228] snd_soc_register_card failed -517

[ 7.656127] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 7.656377] snd_cht_driver_init: CHT-T4-RT5672 Machine driver registered.

[ 7.656407] Cherrytrail Machine Driver cht_rt5645 registerd

[ 7.656766] Cherrytrail Machine Driver cht_aic31xx registerd

[ 7.656813] ALSA device list:

[ 7.656847] #0:

[ 7.659551] Freeing unused kernel memory: 1444K (ffffffff82529000 - ffffffff82692000)

[ 7.659589] Write protecting the kernel read-only data: 18432k

[ 7.661420] Freeing unused kernel memory: 1208K (ffff880001ad2000 - ffff880001c00000)

[ 7.664942] Freeing unused kernel memory: 592K (ffff88000216c000 - ffff880002200000)

[ 7.666225] init: init first stage started!

[ 7.668528] SELinux: 2048 avtab hash slots, 8876 rules.

[ 7.670655] SELinux: 2048 avtab hash slots, 8876 rules.

[ 7.670691] SELinux: 1 users, 2 roles, 812 types, 0 bools, 1 sens, 1024 cats

[ 7.670838] SELinux: 63 classes, 8876 rules

[ 7.671622] SELinux: Completing initialization.

[ 7.671652] SELinux: Setting up existing superblocks.

[ 7.671724] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

[ 7.671777] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts

[ 7.671965] SELinux: initialized (dev bdev, type bdev), not configured for labeling

[ 7.671998] SELinux: initialized (dev proc, type proc), uses genfs_contexts

[ 7.672058] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts

[ 7.687374] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs

[ 7.687416] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs

[ 7.687465] SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for labeling

[ 7.687516] SELinux: initialized (dev aio, type aio), not configured for labeling

[ 7.687569] SELinux: initialized (dev devpts, type devpts), uses transition SIDs

[ 7.687668] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs

[ 7.687705] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts

[ 7.687796] SELinux: initialized (dev drm, type drm), not configured for labeling

[ 7.687829] SELinux: initialized (dev configfs, type configfs), uses genfs_contexts

[ 7.687881] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

[ 7.687941] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts

[ 7.696704] audit: type=1403 audit(1532481706.561:2): policy loaded auid=4294967295 ses=4294967295

[ 7.697123] usb 1-4.3: new full-speed USB device number 4 using xhci_hcd

[ 7.697355] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.697404] init: (Initializing SELinux non-enforcing took 0.03s.)

[ 7.700967] init: init second stage started!

[ 7.703239] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 7.707459] init: Running restorecon...

[ 7.793838] usb 1-4.3: device v1546 p01a8 is not supported

[ 7.800050] usb 1-4.3: New USB device found, idVendor=1546, idProduct=01a8

[ 7.800082] usb 1-4.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[ 7.800133] usb 1-4.3: Product: u-blox GNSS receiver

[ 7.800184] usb 1-4.3: Manufacturer: u-blox AG - www.u-blox.com

[ 7.800645] usb 1-4.3: ep 0x83 - rounding interval to 1024 microframes, ep desc says 2040 microframes

[ 7.804808] audit: type=1400 audit(1532481706.670:3): avc: denied { associate } for pid=1 comm="init" name="entries" dev="sysfs" ino=17044 scontext=u:object_r:dmi_entries_files:s0 tcontext=u:object_r:sysfs:s0 tclass=filesystem permissive=1

[ 7.811699] Product: u-blox GNSS receiver

[ 7.811748] !!!! This is u-blox GPS device !!!!

[ 7.811865] cdc_acm 1-4.3:1.0: ttyACM30: USB ACM device

[ 7.812498] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.812538] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.812675] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 7.820921] snd_soc_register_card failed -517

[ 7.826363] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 7.826728] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.826763] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.826874] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 7.835105] snd_soc_register_card failed -517

[ 7.835221] xhci_hcd 0000:00:14.0: udev[1-4.3]: Check if need unblock ssic runtime, portnum[3] ssic_runtime_blocked[0]

[ 7.835257] hub 1-4:1.0: hub_port_connect------------------

[ 7.839993] audit: type=1400 audit(1532481706.701:4): avc: denied { associate } for pid=1 comm="init" name="ec_fw" dev="sysfs" ino=16584 scontext=u:object_r:ec_fw_files:s0 tcontext=u:object_r:sysfs:s0 tclass=filesystem permissive=1

[ 7.840299] port4: status 0101, change 0000, 12 Mb/s

[ 7.840485] audit: type=1400 audit(1532481706.705:5): avc: denied { associate } for pid=1 comm="init" name="panel_id" dev="sysfs" ino=16079 scontext=u:object_r:panel_id_files:s0 tcontext=u:object_r:sysfs:s0 tclass=filesystem permissive=1

[ 7.846299] init: waitpid failed: No child processes

[ 7.846618] init: (Loading properties from /default.prop took 0.00s.)

[ 7.847842] init: (Parsing /init.environ.rc took 0.00s.)

[ 7.848055] init: (Parsing /init.usb.rc took 0.00s.)

[ 7.848949] init: /init.cht_rvp.rc: 889: invalid keyword 'umount'

[ 7.849109] init: (Parsing /init.logs.rc took 0.00s.)

[ 7.849159] init: (Parsing /init.crashlogd.rc took 0.00s.)

[ 7.849206] init: (Parsing /init.coredump.rc took 0.00s.)

[ 7.849286] init: (Parsing /init.debug-charging.rc took 0.00s.)

[ 7.849323] init: (Parsing /init.diag.rc took 0.00s.)

[ 7.849358] init: (Parsing /init.lmdump.rc took 0.00s.)

[ 7.849388] init: (Parsing /init.log-watch.rc took 0.00s.)

[ 7.849430] init: (Parsing /init.kernel.rc took 0.00s.)

[ 7.849437] init: (Parsing /init.cht_rvp.rc took 0.00s.)

[ 7.849921] init: (Parsing /init.usb.configfs.rc took 0.00s.)

[ 7.849975] init: (Parsing /init.zygote64_32.rc took 0.00s.)

[ 7.849982] init: (Parsing /init.rc took 0.00s.)

[ 7.850392] init: Starting service 'ueventd'...

[ 7.850787] SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts

[ 7.850980] init: Waiting for /dev/.coldboot_done...

[ 7.852395] hub 1-4:1.0: hub_port_connect+++++++++++++

[ 7.852396] hub port 0x101

[ 7.853579] ueventd: ueventd started!

[ 7.858998] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.859000] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 7.898996] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 7.899109] snd_soc_sst_platform: sst_platform_probe deferred

[ 7.899142] platform sst-platform: Driver sst-platform requests probe deferral

[ 7.899284] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 7.907541] snd_soc_register_card failed -517

[ 7.912467] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 7.928127] usb 1-4.4: new high-speed USB device number 5 using xhci_hcd

[ 7.929737] hub 1-4:1.0: hub_port_reset():++++++++++++

[ 7.935570] hub 1-4:1.0: hub_port_reset(): SW Reset Port

[ 8.086093] usb 1-4.4: device v058f p5608 is not supported

[ 8.092334] usb 1-4.4: New USB device found, idVendor=058f, idProduct=5608

[ 8.092370] usb 1-4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[ 8.092419] usb 1-4.4: Product: USB 2.0M Camera

[ 8.092472] usb 1-4.4: Manufacturer: Unison

[ 8.097091] uvcvideo: Found UVC 1.00 device USB 2.0M Camera (058f:5608)

[ 8.106356] input: USB 2.0M Camera as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4.4/1-4.4:1.0/input/input5

[ 8.107939] snd_soc_sst_platform: sst_platform_probe deferred

[ 8.107989] platform sst-platform: Driver sst-platform requests probe deferral

[ 8.108135] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 8.116432] snd_soc_register_card failed -517

[ 8.117956] xhci_hcd 0000:00:14.0: udev[1-4.4]: Check if need unblock ssic runtime, portnum[4] ssic_runtime_blocked[0]

[ 8.118024] hub 1-4:1.0: hub_port_connect------------------

[ 8.139961] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 8.140089] snd_soc_sst_platform: sst_platform_probe deferred

[ 8.140126] platform sst-platform: Driver sst-platform requests probe deferral

[ 8.140305] cht_rt5672 cht_rt5672: ASoC: CPU DAI Headset-cpu-dai not registered

[ 8.148861] snd_soc_register_card failed -517

[ 8.153805] platform cht_rt5672: Driver cht_rt5672 requests probe deferral

[ 8.450799] ueventd: Coldboot took 0.60s.

[ 8.454836] init: Waiting for /dev/.coldboot_done took 0.60s.

[ 8.454945] init: /dev/hw_random not found

[ 8.459719] keychord: using input dev Power Button for fevent

[ 8.459758] keychord: using input dev Power Button for fevent

[ 8.459838] keychord: using input dev gpio-keys for fevent

[ 8.460929] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

[ 8.462484] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

[ 8.466854] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

[ 8.467555] init: write_file: Unable to open '/proc/cpu/alignment': No such file or directory

[ 8.467840] init: write_file: Unable to open '/proc/sys/kernel/sched_compat_yield': No such file or directory

[ 8.469255] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

[ 8.469460] init: write_file: Unable to write to '/dev/cpuctl/cpu.shares': Invalid argument

[ 8.470405] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts

[ 8.474727] SELinux: initialized (dev pstore, type pstore), uses genfs_contexts

[ 8.475010] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory

[ 8.815752] random: nonblocking pool is initialized

[ 8.930329] init: /dev/hw_random not found

[ 8.996215] SELinux: initialized (dev efivarfs, type efivarfs), uses genfs_contexts

[ 9.762019] fs_mgr: Enabling dm-verity for system (mode 2)

[ 9.762082] fs_mgr: loading verity table: '1 /dev/block/by-name/android_system /dev/block/by-name/android_system 4096 4096 645127 645127 sha256 dbcf9a4d38ba4899319381ca6f7407e94e2af39a0f6bc4b862d220afe921a277 aee087a5be3b982978c923f566a94613496b417f2af592639bc80d141e34dfe7 10 restart_on_corruption use_fec_from_device /dev/block/by-name/android_system fec_start 650217 fec_blocks 650217 fec_roots 2 ignore_zero_blocks'

[ 9.778057] bio: create slab <bio-1> at 1

[ 9.792160] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)

[ 9.792212] SELinux: initialized (dev dm-0, type ext4), uses xattr

[ 9.792313] fs_mgr: __mount(source=/dev/block/dm-0,target=/system,type=ext4)=0

[ 9.793140] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option

[ 9.803602] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit

[ 9.803668] SELinux: initialized (dev mmcblk0p8, type ext4), uses xattr

[ 9.803753] fs_mgr: check_fs(): mount(/dev/block/by-name/android_cache,/cache,ext4)=0: Success

[ 9.815628] fs_mgr: check_fs(): unmount(/cache) succeeded

[ 9.823753] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/android_cache

[ 9.845991] [drm] Loading HuC

[ 9.846684] [drm] HuC loaded successfully

[ 9.966801] e2fsck: e2fsck 1.42.9 (28-Dec-2013)

[ 9.966801]

[ 9.966860] e2fsck: Pass 1: Checking inodes, blocks, and sizes

[ 9.966860]

[ 9.966894] e2fsck: Pass 2: Checking directory structure

[ 9.966894]

[ 9.966944] e2fsck: Pass 3: Checking directory connectivity

[ 9.966944]

[ 9.966995] e2fsck: Pass 4: Checking reference counts

[ 9.966995]

[ 9.967046] e2fsck: Pass 5: Checking group summary information

[ 9.967046]

[ 9.967098] e2fsck: cache: 14/6400 files (0.0% non-contiguous), 1442/25600 blocks

[ 9.967098]

[ 9.970472] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: errors=panic

[ 9.970518] SELinux: initialized (dev mmcblk0p8, type ext4), uses xattr

[ 9.970604] fs_mgr: __mount(source=/dev/block/by-name/android_cache,target=/cache,type=ext4)=0

[ 9.971326] EXT4-fs (mmcblk0p9): VFS: Can't find ext4 filesystem

[ 9.978122] fs_mgr: check_fs(): mount(/dev/block/by-name/android_data,/data,ext4)=-1: Invalid argument

[ 9.978164] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/android_data

[ 9.992474] e2fsck: e2fsck 1.42.9 (28-Dec-2013)

[ 9.992474]

[ 9.992527] e2fsck: ext2fs_open2: Bad magic number in super-block

[ 9.992527]

[ 9.992566] e2fsck: /system/bin/e2fsck: Superblock invalid, trying backup blocks...

[ 9.992566]

[ 9.992617] e2fsck: /system/bin/e2fsck: Bad magic number in super-block while trying to open /dev/block/by-name/android_data

[ 9.992617]

[ 9.992687] e2fsck:

[ 9.992687]

[ 9.992719] e2fsck: The superblock could not be read or does not describe a correct ext2

[ 9.992719]

[ 9.992770] e2fsck: filesystem. If the device is valid and it really contains an ext2

[ 9.992770]

[ 9.992821] e2fsck: filesystem (and not swap or ufs or something else), then the superblock

[ 9.992821]

[ 9.992872] e2fsck: is corrupt, and you might try running e2fsck with an alternate superblock:

[ 9.992872]

[ 9.992923] e2fsck: e2fsck -b 8193 <device>

[ 9.992923]

[ 9.992974] e2fsck:

[ 9.992974]

[ 9.993030] e2fsck: e2fsck terminated by exit(8)

[ 9.993030]

[ 9.993805] EXT4-fs (mmcblk0p9): VFS: Can't find ext4 filesystem

[ 10.000668] fs_mgr: __mount(source=/dev/block/by-name/android_data,target=/data,type=ext4)=-1

[ 10.001567] fs_mgr: fs_mgr_mount_all(): possibly an encryptable blkdev /dev/block/by-name/android_data for mount /data type ext4 )

[ 10.014832] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs

[ 10.015788] EXT4-fs (mmcblk0p11): Ignoring removed nomblk_io_submit option

[ 10.026547] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit

[ 10.026589] SELinux: initialized (dev mmcblk0p11, type ext4), uses xattr

[ 10.026692] fs_mgr: check_fs(): mount(/dev/block/by-name/android_config,/oem_config,ext4)=0: Success

[ 10.040555] fs_mgr: check_fs(): unmount(/oem_config) succeeded

[ 10.040703] fs_mgr: Running /system/bin/e2fsck on /dev/block/by-name/android_config

[ 10.074384] e2fsck: e2fsck 1.42.9 (28-Dec-2013)

[ 10.074384]

[ 10.074445] e2fsck: Pass 1: Checking inodes, blocks, and sizes

[ 10.074445]

[ 10.074483] e2fsck: Pass 2: Checking directory structure

[ 10.074483]

[ 10.074533] e2fsck: Pass 3: Checking directory connectivity

[ 10.074533]

[ 10.074584] e2fsck: Pass 4: Checking reference counts

[ 10.074584]

[ 10.074660] e2fsck: Pass 5: Checking group summary information

[ 10.074660]

[ 10.074703] e2fsck: /dev/block/by-name/android_config: 11/512 files (0.0% non-contiguous), 1071/2048 blocks

[ 10.074703]

[ 10.078376] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: errors=panic

[ 10.078423] SELinux: initialized (dev mmcblk0p11, type ext4), uses xattr

[ 10.078514] fs_mgr: __mount(source=/dev/block/by-name/android_config,target=/oem_config,type=ext4)=0

[ 10.082193] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: (null)

[ 10.082232] SELinux: initialized (dev mmcblk0p12, type ext4), uses xattr

[ 10.082315] fs_mgr: __mount(source=/dev/block/by-name/android_factory,target=/factory,type=ext4)=0

[ 10.085155] init: (Parsing /system/etc/init/atrace.rc took 0.00s.)

[ 10.086096] init: (Parsing /system/etc/init/audioserver.rc took 0.00s.)

[ 10.087051] init: (Parsing /system/etc/init/bootanim.rc took 0.00s.)

[ 10.087766] init: (Parsing /system/etc/init/bootstat.rc took 0.00s.)

[ 10.088850] init: (Parsing /system/etc/init/cameraserver.rc took 0.00s.)

[ 10.089667] init: (Parsing /system/etc/init/debuggerd.rc took 0.00s.)

[ 10.090755] init: (Parsing /system/etc/init/debuggerd64.rc took 0.00s.)

[ 10.091543] init: (Parsing /system/etc/init/drmserver.rc took 0.00s.)

[ 10.092455] init: (Parsing /system/etc/init/dumpstate.rc took 0.00s.)

[ 10.093380] init: (Parsing /system/etc/init/gatekeeperd.rc took 0.00s.)

[ 10.094166] init: (Parsing /system/etc/init/init-debug.rc took 0.00s.)

[ 10.094971] init: (Parsing /system/etc/init/installd.rc took 0.00s.)

[ 10.095881] init: (Parsing /system/etc/init/keystore.rc took 0.00s.)

[ 10.096595] init: (Parsing /system/etc/init/lmkd.rc took 0.00s.)

[ 10.097442] init: (Parsing /system/etc/init/logcatd.rc took 0.00s.)

[ 10.098258] init: (Parsing /system/etc/init/logd.rc took 0.00s.)

[ 10.099162] init: (Parsing /system/etc/init/mdnsd.rc took 0.00s.)

[ 10.099766] init: (Parsing /system/etc/init/mediacodec.rc took 0.00s.)

[ 10.100403] init: (Parsing /system/etc/init/mediadrmserver.rc took 0.00s.)

[ 10.101247] init: (Parsing /system/etc/init/mediaextractor.rc took 0.00s.)

[ 10.102154] init: (Parsing /system/etc/init/mediaserver.rc took 0.00s.)

[ 10.102964] init: (Parsing /system/etc/init/mtpd.rc took 0.00s.)

[ 10.103793] init: (Parsing /system/etc/init/netd.rc took 0.00s.)

[ 10.104655] init: (Parsing /system/etc/init/perfprofd.rc took 0.00s.)

[ 10.105714] init: (Parsing /system/etc/init/racoon.rc took 0.00s.)

[ 10.106685] init: (Parsing /system/etc/init/rild.rc took 0.00s.)

[ 10.107674] init: (Parsing /system/etc/init/servicemanager.rc took 0.00s.)

[ 10.108520] init: (Parsing /system/etc/init/surfaceflinger.rc took 0.00s.)

[ 10.109480] init: (Parsing /system/etc/init/uncrypt.rc took 0.00s.)

[ 10.110314] init: (Parsing /system/etc/init/vdc.rc took 0.00s.)

[ 10.111102] init: (Parsing /system/etc/init/vold.rc took 0.00s.)

[ 10.347805] init: Starting service 'logd'...

[ 10.403081] logd.auditd: start

[ 10.403158] logd.klogd: 10376519360

[ 10.415315] logd.klogd: sync at 2018-07-25 01:21:49.280881544 UTC

[ 10.771562] init: insmod: open("/lib/modules/lm_dump.ko") failed: No such file or directoryinit: (Loading properties from /system/build.prop took 0.00s.)

[ 10.782233] init: (Loading properties from /vendor/build.prop took 0.00s.)

[ 10.783025] init: (Loading properties from /factory/factory.prop took 0.00s.)

[ 10.784864] init: Starting service 'debuggerd'...

[ 10.785403] init: Starting service 'debuggerd64'...

[ 10.787107] init: Starting service 'vold'...

[ 10.788332] init: Not bootcharting.

[ 11.290996] init: Starting service 'exec 1 (/system/bin/tzdatacheck)'...

[ 11.312312] init: Service 'exec 1 (/system/bin/tzdatacheck)' (pid 2479) exited with status 0

[ 11.314292] init: Service wlan_prov does not have a SELinux domain defined.

[ 16.365095] input: accel_b as /devices/pci0000:00/808622C1:02/i2c-2/i2c-BOSC0200:00/input/input6

[ 16.366396] ------------[ cut here ]------------

[ 16.371732] register i2c driver BOSC0200:00

[ 16.371807] i2c i2c-2: Failed to register i2c client BOSC0200:00 at 0x18 (-16)

[ 16.371879] WARNING: CPU: 0 PID: 41 at /media/ethanma/workspace/d42/trunk_nougat_70/kernel/cht/drivers/base/dd.c:286 driver_probe_device+0x189/0x400()

[ 16.371890] Modules linked in:

[ 16.371904] CPU: 0 PID: 41 Comm: kworker/u8:1 Tainted: G W 3.14.79-x86_64-svn6727 #131

[ 16.371909] Hardware name: Insyde CherryTrail/Type2 - Board Product Name, BIOS D420V101(D420-10103) 05/24/2018

[ 16.371926] Workqueue: deferwq deferred_probe_work_func

[ 16.371946] 0000000000000000 ffff880179f7bcc0 ffffffff81ab5e56 0000000000000000

[ 16.371960] 0000000000000009 ffff880179f7bcf8 ffffffff8108b89d ffff880100518010

[ 16.371974] ffffffff8248e568 ffffffff815a0810 000000000000000c ffffffff82426280

[ 16.371977] Call Trace:

[ 16.372002] [<ffffffff81ab5e56>] dump_stack+0x67/0x90

[ 16.372019] [<ffffffff8108b89d>] warn_slowpath_common+0x7d/0xa0

[ 16.372034] [<ffffffff815a0810>] ? driver_probe_device+0x400/0x400

[ 16.372046] [<ffffffff8108b97a>] warn_slowpath_null+0x1a/0x20

[ 16.372058] [<ffffffff815a0599>] driver_probe_device+0x189/0x400

[ 16.372070] [<ffffffff815a0810>] ? driver_probe_device+0x400/0x400

[ 16.372082] [<ffffffff815a084b>] __device_attach+0x3b/0x40

[ 16.372095] [<ffffffff8159e3b3>] bus_for_each_drv+0x63/0xa0

[ 16.372107] [<ffffffff815a03a8>] device_attach+0x88/0xa0

[ 16.372119] [<ffffffff8159f7a0>] bus_probe_device+0xa0/0xc0

[ 16.372132] [<ffffffff8159fcd8>] deferred_probe_work_func+0x38/0xe0

[ 16.372146] [<ffffffff810a900f>] process_one_work+0x16f/0x4f0

[ 16.372162] [<ffffffff810a9d9c>] worker_thread+0x12c/0x3d0

[ 16.372175] [<ffffffff810a9c70>] ? manage_workers.isra.27+0x290/0x290

[ 16.372188] [<ffffffff810afd5d>] kthread+0xed/0x110

[ 16.372203] [<ffffffff810afc70>] ? kthread_create_on_node+0x190/0x190

[ 16.372216] [<ffffffff81acb008>] ret_from_fork+0x58/0x90

[ 16.372228] [<ffffffff810afc70>] ? kthread_create_on_node+0x190/0x190

[ 16.372236] ---[ end trace a26738ab24f91438 ]---

[ 16.378609] sst-platform sst-platform: ASoC: no sink widget found for Audio Capture

[ 16.378623] sst-platform sst-platform: ASoC: Failed to add route media3_out -> direct -> Audio Capture

[ 16.412812] Codec driver version 0.0.6 alsa 1.0.25

[ 16.540795] rt5670 i2c-10EC5672:00: ASoC: no source widget found for Mono ADC MIX

[ 16.540798] rt5670 i2c-10EC5672:00: ASoC: Failed to add route Mono ADC MIX -> Slot 2-3 -> TDM Data Mux

[ 16.557226] rt5670 i2c-10EC5672:00: ASoC: no source widget found for 8CH TDM Data

[ 16.557228] rt5670 i2c-10EC5672:00: ASoC: Failed to add route 8CH TDM Data -> direct -> DSP Upstream

[ 16.557263] snd-soc-dummy snd-soc-dummy: ASoC: Failed to create platform debugfs directory

[ 16.565092] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> Headset-cpu-dai mapping ok

[ 16.565150] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> Deepbuffer-cpu-dai mapping ok

[ 16.565193] compress asoc: snd-soc-dummy-dai <-> Compress-cpu-dai mapping ok

[ 16.565266] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> Voip-cpu-dai mapping ok

[ 16.565338] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> Lowlatency-cpu-dai mapping ok

[ 16.565590] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> Probe-cpu-dai mapping ok

[ 16.565752] cht_rt5672 cht_rt5672: rt5670-aif1 <-> ssp2-port mapping ok

[ 16.565780] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> snd-soc-dummy-dai mapping ok

[ 16.565811] cht_rt5672 cht_rt5672: snd-soc-dummy-dai <-> snd-soc-dummy-dai mapping ok

[ 16.566089] jack get gpio status 1

[ 16.566093] snd_soc_jack_report jack 0x0 mask 0x7003

[ 16.567854] rt5670 i2c-10EC5672:00: ASoC: mux Mono ADC R Mux has no paths

[ 16.567863] rt5670 i2c-10EC5672:00: ASoC: mux Mono ADC L Mux has no paths

[ 16.568127] rt5670 i2c-10EC5672:00: ASoC: mux INR Mux has no paths

[ 16.568134] rt5670 i2c-10EC5672:00: ASoC: mux INL Mux has no paths

[ 16.581305] input: cherrytrailaud Intel MID Audio Jack as /devices/platform/cht_rt5672/sound/card1/input7

[ 16.581908] keychord: using input dev cherrytrailaud Intel MID Audio Jack for fevent

[ 16.645269] Fail to add i2c device2:24

[ 16.650468] Fail to register sensor device

[ 16.662152] input: cm32181 as /devices/pci0000:00/808622C1:02/i2c-2/i2c-CPLM3218:00/input/input8

[ 16.667379] register i2c driver CPLM3218:00

[ 16.667537] i2c i2c-2: Failed to register i2c client CPLM3218:00 at 0x10 (-16)

[ 16.675733] Fail to add i2c device2:16

[ 16.680035] Fail to register sensor device

[ 16.690978] input: gyro as /devices/pci0000:00/808622C1:02/i2c-2/i2c-SMO8501:00/input/input9

[ 16.692953] register i2c driver SMO8501:00

[ 16.693009] i2c i2c-2: Failed to register i2c client SMO8501:00 at 0x6b (-16)

[ 16.701305] Fail to add i2c device2:107

[ 16.705674] Fail to register sensor device

[ 16.715130] init: (Loading properties from /data/local.prop took 0.00s.)

[ 16.715561] init: Starting service 'logd-reinit'...

[ 16.721702] init: Starting service 'healthd'...

[ 16.722260] init: Starting service 'watchdogd'...

[ 16.723504] init: Starting service 'init-dev-prop'...

[ 16.724564] init: Starting service 'keymaster_meid'...

[ 16.725598] init: Starting service 'intel_prop'...

[ 16.726516] init: Starting service 'earlylogs'...

[ 16.727364] init: Starting service 'lmkd'...

[ 16.728283] init: Starting service 'servicemanager'...

[ 16.730822] init: Starting service 'surfaceflinger'...

[ 16.733253] init: couldn't write 2516 to /sys/fs/cgroup/stune/foreground/tasks: No such file or directory

[ 16.738017] binder: 2508:2508 transaction failed 29189, size 0-0

[ 16.738043] watchdogd: started (interval 10, margin 30)!

[ 16.744737] lm3554 i2c-INTCF1C:00: camera pdata: lm3554: reset: 394 strobe 397 torch 386

[ 16.744762] logd.daemon: reinit

[ 16.744849] lm3554 i2c-INTCF1C:00: flash led reset successfully

[ 16.744903] lm3554 i2c-INTCF1C:00: register atomisp i2c module type 4

[ 16.744939] lm3554 i2c-INTCF1C:00: gmin: initializing atomisp module subdev data.PMIC ID 4

[ 16.744988] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_CamClk

[ 16.753258] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_ClkSrc

[ 16.762007] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_CsiPort

[ 16.770723] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_CsiLanes

[ 16.779583] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo1_1p8v

[ 16.788252] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo1_sel_reg

[ 16.797164] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo1_ctrl_shift

[ 16.806380] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo2_1p8v

[ 16.815278] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo2_sel_reg

[ 16.824182] acpi INTCF1C:00: gmin_get_config_var() dev_name INTCF1C:00_eldo2_ctrl_shift

[ 16.834078] init: Service 'logd-reinit' (pid 2507) exited with status 0

[ 16.848770] type=1400 audit(1532481715.714:6): avc: denied { search } for pid=2512 comm="intel_prop" name="entries" dev="sysfs" ino=17044 scontext=u:r:intel_prop:s0 tcontext=u:object_r:dmi_entries_files:s0 tclass=dir permissive=1

[ 16.854708] type=1400 audit(1532481715.714:7): avc: denied { read } for pid=2512 comm="intel_prop" name="raw" dev="sysfs" ino=17051 scontext=u:r:intel_prop:s0 tcontext=u:object_r:dmi_entries_files:s0 tclass=file permissive=1

[ 16.854801] type=1400 audit(1532481715.714:8): avc: denied { open } for pid=2512 comm="intel_prop" path="/sys/firmware/dmi/entries/0-0/raw" dev="sysfs" ino=17051 scontext=u:r:intel_prop:s0 tcontext=u:object_r:dmi_entries_files:s0 tclass=file permissive=1

[ 16.855097] cfg80211: Calling CRDA to update world regulatory domain

[ 16.858135] type=1400 audit(1532481715.722:9): avc: denied { search } for pid=2525 comm="init-dev-prop.s" name="ec_fw" dev="sysfs" ino=16584 scontext=u:r:init-dev-prop:s0 tcontext=u:object_r:ec_fw_files:s0 tclass=dir permissive=1

[ 16.859974] PANEL_ID_1=1

[ 16.860151] PANEL_ID_2=1

[ 16.860188] PANEL_ID_3=1

[ 16.860236] PANEL_ID_4=1

[ 16.860288] >>>> get_panel_id : PANEL_ID_NUM=0xf

[ 16.860503] type=1400 audit(1532481715.725:10): avc: denied { search } for pid=2527 comm="init-dev-prop.s" name="panel_id" dev="sysfs" ino=16079 scontext=u:r:init-dev-prop:s0 tcontext=u:object_r:panel_id_files:s0 tclass=dir permissive=1

[ 16.908303] RTW: module init start

[ 16.908341] RTW: rtl8821au v5.2.6.3_25025.20171106_COEX20171103-6c6d

[ 16.908397] RTW: build time: Jun 28 2018 15:36:12

[ 16.908472] RTW: rtl8821au BT-Coex version = COEX20171103-6c6d

[ 16.908629] RTW:

[ 16.908629] usb_endpoint_descriptor(0):

[ 16.908664] RTW: bLength=7

[ 16.908714] RTW: bDescriptorType=5

[ 16.908764] RTW: bEndpointAddress=84

[ 16.908816] RTW: wMaxPacketSize=512

[ 16.908867] RTW: bInterval=0

[ 16.908918] RTW: RT_usb_endpoint_is_bulk_in = 4

[ 16.908969] RTW:

[ 16.908969] usb_endpoint_descriptor(1):

[ 16.909020] RTW: bLength=7

[ 16.909072] RTW: bDescriptorType=5

[ 16.909123] RTW: bEndpointAddress=5

[ 16.909174] RTW: wMaxPacketSize=512

[ 16.909225] RTW: bInterval=0

[ 16.909276] RTW: RT_usb_endpoint_is_bulk_out = 5

[ 16.909328] RTW:

[ 16.909328] usb_endpoint_descriptor(2):

[ 16.909379] RTW: bLength=7

[ 16.909470] RTW: bDescriptorType=5

[ 16.909503] RTW: bEndpointAddress=6

[ 16.909553] RTW: wMaxPacketSize=512

[ 16.909604] RTW: bInterval=0

[ 16.909655] RTW: RT_usb_endpoint_is_bulk_out = 6

[ 16.909707] RTW:

[ 16.909707] usb_endpoint_descriptor(3):

[ 16.909759] RTW: bLength=7

[ 16.909809] RTW: bDescriptorType=5

[ 16.909862] RTW: bEndpointAddress=87

[ 16.909912] RTW: wMaxPacketSize=64

[ 16.909966] RTW: bInterval=3

[ 16.910014] RTW: RT_usb_endpoint_is_int_in = 7, Interval = 3

[ 16.910065] RTW:

[ 16.910065] usb_endpoint_descriptor(4):

[ 16.910118] RTW: bLength=7

[ 16.910168] RTW: bDescriptorType=5

[ 16.910219] RTW: bEndpointAddress=8

[ 16.910275] RTW: wMaxPacketSize=512

[ 16.910333] RTW: bInterval=0

[ 16.910384] RTW: RT_usb_endpoint_is_bulk_out = 8

[ 16.910454] RTW:

[ 16.910454] usb_endpoint_descriptor(5):

[ 16.910488] RTW: bLength=7

[ 16.910538] RTW: bDescriptorType=5

[ 16.910589] RTW: bEndpointAddress=9

[ 16.910640] RTW: wMaxPacketSize=512

[ 16.910692] RTW: bInterval=0

[ 16.910746] RTW: RT_usb_endpoint_is_bulk_out = 9

[ 16.910795] RTW: nr_endpoint=6, in_num=2, out_num=4

[ 16.910795]

[ 16.910845] RTW: USB_SPEED_HIGH

[ 16.910897] RTW: CHIP TYPE: RTL8811AU or RTL8821U

[ 16.911095] RTW: read_chip_version_8812a SYS_CFG(0xF0)=0x04412135

[ 16.911203] RTW: rtw_hal_config_rftype RF_Type is 3 TotalTxPath is 1

[ 16.911239] RTW: Chip Version Info: CHIP_8821_Normal_Chip_TSMC_C_CUT_1T1R_RomVer(0)

[ 16.911289] RTW: _ConfigChipOutEP_8812 OutEpQueueSel(0x07), OutEpNumber(4)

[ 16.911388] RTW: Boot from EFUSE, Autoload OK !

[ 16.966437] snd_soc_jack_report jack 0x0 mask 0x7003

[ 16.994841] RTW: Hal_EfuseReadEFuse8812A: eFuse_Addr offset(0xa8) !!

[ 16.994913] RTW: HW EFUSE

[ 16.994943] RTW: 0x000: 29 81 00 7C 01 00 01 00 4C 00 05 35 10 00 00 00

[ 16.996021] RTW: 0x010: 27 28 28 27 27 27 2C 2C 2D 2A 2A 0E FF FF FF FF

[ 16.996891] RTW: 0x020: FF FF 28 27 25 20 2B 28 28 28 28 27 26 25 22 21

[ 16.997762] RTW: 0x030: 00 FF FF FF FF FF 00 FF FF FF FF FF FF FF FF FF

[ 16.998843] RTW: 0x040: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 16.999714] RTW: 0x050: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.000584] RTW: 0x060: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.001672] RTW: 0x070: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.002542] RTW: 0x080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.003423] RTW: 0x090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.004483] RTW: 0x0a0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.005353] RTW: 0x0b0: FF FF FF FF FF FF FF FF 7F 0E 1B 00 00 00 FF 00

[ 17.006468] RTW: 0x0c0: FF 29 20 10 00 00 00 55 00 FF FF FF FF FF FF FF

[ 17.007337] RTW: 0x0d0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.008208] RTW: 0x0e0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.009278] RTW: 0x0f0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.010147] RTW: 0x100: DA 0B 23 08 E7 47 03 BC 25 F0 1A 83 62 0A 03 52

[ 17.011045] RTW: 0x110: 65 61 6C 74 65 6B 20 18 03 38 30 32 2E 31 31 61

[ 17.012129] RTW: 0x120: 63 20 57 4C 41 4E 20 41 64 61 70 74 65 72 20 00

[ 17.013000] RTW: 0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.013870] RTW: 0x140: FF FF FF FF FF FF FF 0F FF FF FF FF FF FF FF FF

[ 17.014742] RTW: 0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.015614] RTW: 0x160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.016485] RTW: 0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.017360] RTW: 0x180: FF FF FF FF FF FF FF FF 83 AB 99 2D 03 93 98 A0

[ 17.018232] RTW: 0x190: FC 8C 00 11 9B C4 00 FF FF FF FF FF FF FF FF FF

[ 17.019101] RTW: 0x1a0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.019971] RTW: 0x1b0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.020867] RTW: 0x1c0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.021738] RTW: 0x1d0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.022608] RTW: 0x1e0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.023478] RTW: 0x1f0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

[ 17.024641]

[ 17.024694] RTW: EEPROM ID=0x8129

[ 17.024744] RTW: VID = 0x0BDA, PID = 0x0823

[ 17.024794] RTW: Customer ID: 0x00, SubCustomer ID: 0xCD

[ 17.024857] RTW: EEPROMRegulatory = 0x1

[ 17.024896] RTW: Board Type: 0x 1

[ 17.025006] RTW: Hal_EfuseParseBTCoexistInfo8812A: BTCoexist=Enable, AntNum=2, AntPath=0

[ 17.025037] RTW: hal_com_config_channel_plan chplan:0x7F

[ 17.025087] RTW: crystal_cap: 0x e

[ 17.025137] RTW: ThermalMeter = 0x1b

[ 17.025189] RTW: Hal_ReadRemoteWakeup_8812A...bSupportRemoteWakeup(1)

[ 17.025241] RTW: pHalData->PAType_2G is 0x0, pHalData->ExternalPA_2G = 0

[ 17.025291] RTW: pHalData->PAType_5G is 0x0, pHalData->external_pa_5g = 0

[ 17.025342] RTW: pHalData->LNAType_2G is 0x0, pHalData->ExternalLNA_2G = 0

[ 17.025415] RTW: pHalData->LNAType_5G is 0x0, pHalData->external_lna_5g = 0

[ 17.025445] RTW: Usb Switch: 0

[ 17.025496] RTW: PID= 0x823, VID= bda

[ 17.025548] RTW: PID= 0x823, VID= bda

[ 17.025598] RTW: Customer ID: 0x 0

[ 17.026202] RTW: hal_ReadUsbType_8812AU: antenna=7, wmode=3

[ 17.026232] RTW: rtw_hal_read_chip_info in 115 ms

[ 17.026361] RTW: init_channel_set((null)) ChannelPlan ID:0x7f, ch num:37

[ 17.026601] RTW: NR_RECVBUFF: 8

[ 17.026694] RTW: MAX_RECVBUF_SZ: 32768

[ 17.026748] RTW: NR_PREALLOC_RECV_SKB: 8

[ 17.026904] RTW: rtw_alloc_macid((null)) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1

[ 17.026965] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1

[ 17.027039] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~~~~

[ 17.027067] RTW: pwrctrlpriv.bSupportRemoteWakeup~~~[1]~~~

[ 17.027121] RTW: can't get autopm:

[ 17.027171] RTW: rtw_get_mac_addr_intel Enter

[ 17.027279] RTW: retriveFromFile openFile path:/config/wifi/mac.txt Fail, ret:-2

[ 17.027311] RTW: rtw_macaddr_cfg mac addr:bc:25:f0:1a:83:62

[ 17.027361] RTW: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0

[ 17.027566] RTW: init_channel_set((null)) ChannelPlan ID:0x7f, ch num:37

[ 17.027821] RTW: NR_RECVBUFF: 8

[ 17.027851] RTW: MAX_RECVBUF_SZ: 32768

[ 17.027907] RTW: NR_PREALLOC_RECV_SKB: 8

[ 17.028063] RTW: rtw_alloc_macid((null)) if2, hwaddr:ff:ff:ff:ff:ff:ff macid:1

[ 17.028100] RTW: rtw_drv_add_vir_if if2 mac_addr : be:25:f0:1a:83:62

[ 17.028176] RTW: rtw_wiphy_alloc(phy0)

[ 17.028206] RTW: rtw_wdev_alloc(padapter=ffffc90004578000)

[ 17.028271] RTW: rtw_wiphy_alloc(phy1)

[ 17.028308] RTW: rtw_wdev_alloc(padapter=ffffc90004614000)

[ 17.028360] RTW: rtw_wiphy_register(phy0)

[ 17.028429] RTW: Register RTW cfg80211 vendor cmd(0x67) interface

[ 17.031740] RTW: rtw_ndev_init(wlan0) if1 mac_addr=bc:25:f0:1a:83:62

[ 17.031931] RTW: rtw_ndev_notifier_call(wlan0) state:16

[ 17.035527] RTW: rtw_ndev_notifier_call(wlan0) state:5

[ 17.035616] RTW: rtw_wiphy_register(phy1)

[ 17.035655] RTW: Register RTW cfg80211 vendor cmd(0x67) interface

[ 17.036755] RTW: rtw_ndev_init(p2p0) if2 mac_addr=be:25:f0:1a:83:62

[ 17.037282] RTW: rtw_ndev_notifier_call(p2p0) state:16

[ 17.040926] RTW: rtw_ndev_notifier_call(p2p0) state:5

[ 17.041292] usbcore: registered new interface driver rtl8821au

[ 17.041333] RTW: module init ret=0

[ 17.042346] init: Service 'intel_prop' (pid 2512) exited with status 0

[ 17.042595] init: Service 'earlylogs' (pid 2513) exited with status 0

[ 17.051272] init: Starting service 'rfkill-init'...

[ 17.060005] rtk_btusb: RTKBT_RELEASE_NAME: 20170302_BT_ANDROID_7.0

[ 17.060048] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.4

[ 17.060096] rtk_btusb: Register usb char device interface for BT driver

[ 17.061892] rtk_btusb: btusb_probe: usb_interface ffff880002c7dc00, bInterfaceNumber 0, idVendor 0x0bda, idProduct 0x0000

[ 17.061938] rtk_btusb: get_fw_table_entry: Product id = 0x0823, fw table entry size 49

[ 17.061982] rtk_btusb: firmware_info_init: Auto suspend is disabled

[ 17.062032] rtk_btusb: btusb_probe: download begining...

[ 17.062083] rtk_btusb: btusb_probe: download ending...

[ 17.062166] rtk_btusb: btusb_probe: Check bt reset flag 0

[ 17.062720] usbcore: registered new interface driver rtk_btusb

[ 17.066460] pn544_nfc: module is from the staging directory, the quality is unknown, you have been warned.

[ 17.078350] pn544 i2c-NXP1001:00: pn544_probe : irq gpio: 493

[ 17.078386] pn544 i2c-NXP1001:00: pn544_probe : ven gpio: 495

[ 17.078465] pn544 i2c-NXP1001:00: pn544_probe : fw gpio: 496

[ 17.078496] pn544 i2c-NXP1001:00: pn544_probe : i2c xfer size: 0

[ 17.100438] pn544_platform_init : sending reset cmd

[ 17.101080] pn544_platform_init : retry=2, ret=-121

[ 17.122470] pn544_platform_init : sending reset cmd

[ 17.123168] pn544_platform_init : retry=1, ret=-121

[ 17.144503] pn544_platform_init : sending reset cmd

[ 17.145252] pn544_platform_init : retry=0, ret=-121

[ 17.166445] pn544_platform_init : sending reset cmd

[ 17.167158] pn544_platform_init : retry=2, ret=-121

[ 17.190474] pn544_platform_init : sending reset cmd

[ 17.191140] pn544_platform_init : retry=1, ret=-121

[ 17.212416] pn544_platform_init : sending reset cmd

[ 17.213116] pn544_platform_init : retry=0, ret=-121

[ 17.234524] pn544_platform_init : sending reset cmd

[ 17.234909] pn544_platform_init : retry=2, ret=-121

[ 17.256431] pn544_platform_init : sending reset cmd

[ 17.257133] pn544_platform_init : retry=1, ret=-121

[ 17.278485] pn544_platform_init : sending reset cmd

[ 17.279147] pn544_platform_init : retry=0, ret=-121

[ 17.300454] pn544_platform_init : sending reset cmd

[ 17.301250] pn544_platform_init : retry=2, ret=-121

[ 17.322774] pn544_platform_init : sending reset cmd

[ 17.323730] pn544_platform_init : retry=1, ret=-121

[ 17.345436] pn544_platform_init : sending reset cmd

[ 17.346252] pn544_platform_init : retry=0, ret=-121

[ 17.346292] pn544_platform_init : could not detect nfc_en polarity, fallback to active high

[ 17.355754] pn544_probe : can't detect NXP PN544, ret=-121

[ 17.362835] pn544: probe of i2c-NXP1001:00 failed with error -121

[ 17.371238] init: Service 'init-dev-prop' (pid 2510) exited with status 0

[ 17.371459] init: Service 'rfkill-init' (pid 2559) exited with status 0

[ 17.407275] ftrace: Allocated trace_printk buffers

[ 17.409488] atomisp-css2401a0_v21 0000:00:03.0: ISP HPLL frequency base = 1600 MHz

[ 17.409566] atomisp-css2401a0_v21 0000:00:03.0: irq 142 for MSI/MSI-X

[ 17.410160] atomisp-css2401a0_v21 0000:00:03.0: Subdev INT33BE:00 successfully register

[ 17.424670] atomisp-css2401a0_v21 0000:00:03.0: Subdev INTCF1C:00 successfully register

[ 17.475614] atomisp-css2401a0_v21 0000:00:03.0: hmm_reserved_pool init successfully,hmm_reserved_pool is with 32768 pages.

[ 17.480234] init: Starting service 'bootanim'...

[ 17.481859] file system registered

[ 17.488953] using random self ethernet address

[ 17.494219] using random host ethernet address

[ 17.501494] SELinux: initialized (dev functionfs, type functionfs), uses genfs_contexts

[ 17.503786] init: decode_uid: Unable to find UID for 'radio.radio'. Returning UINT_MAX

[ 17.520581] usbcore: registered new interface driver sierra

[ 17.520763] usbserial: USB Serial support registered for Sierra USB modem

[ 17.520812] sierra: v.1.7.43_android_generic_2:USB Driver for Sierra Wireless USB modems

[ 17.536664] GobiNet: 2017-07-10/SWI_2.46.1 Android

[ 17.537852] usbcore: registered new interface driver GobiNet

[ 17.538706] init: Starting service 'console'...

[ 17.546742] init: Starting service 'gfxd'...

[ 17.549506] init: Starting service 'exec 2 (/system/bin/vdc)'...

[ 17.561480] init: Service 'exec 2 (/system/bin/vdc)' (pid 2620) exited with status 0

[ 17.565778] type=1400 audit(1532481716.431:11): avc: denied { dac_override } for pid=2618 comm="sh" capability=1 scontext=u:r:shell:s0 tcontext=u:r:shell:s0 tclass=capability permissive=1

[ 17.574941] type=1400 audit(1532481716.440:12): avc: denied { dac_override } for pid=2619 comm="gfxd" capability=1 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=capability permissive=1

[ 17.576691] type=1400 audit(1532481716.440:13): avc: denied { execute } for pid=2624 comm="gfxd" name="sh" dev="dm-0" ino=373 scontext=u:r:gfxd:s0 tcontext=u:object_r:shell_exec:s0 tclass=file permissive=1

[ 17.576974] type=1400 audit(1532481716.440:14): avc: denied { read open } for pid=2624 comm="gfxd" path="/system/bin/sh" dev="dm-0" ino=373 scontext=u:r:gfxd:s0 tcontext=u:object_r:shell_exec:s0 tclass=file permissive=1

[ 17.580666] init: write_file: Unable to open '/config/usb_gadget/g1/functions/mtp.gs0/os_desc/interface.MTP/compatible_id': No such file or directory

[ 17.580830] init: Starting service 'adbd'...

[ 17.581907] init: write_file: Unable to open '/config/usb_gadget/g1/functions/mtp.gs0/os_desc/interface.MTP/compatible_id': No such file or directory

[ 17.583157] type=1400 audit(1532481716.444:15): avc: denied { execute_no_trans } for pid=2624 comm="gfxd" path="/system/bin/sh" dev="dm-0" ino=373 scontext=u:r:gfxd:s0 tcontext=u:object_r:shell_exec:s0 tclass=file permissive=1

[ 17.583289] type=1400 audit(1532481716.445:16): avc: denied { getattr } for pid=2624 comm="sh" path="/system/bin/sh" dev="dm-0" ino=373 scontext=u:r:gfxd:s0 tcontext=u:object_r:shell_exec:s0 tclass=file permissive=1

[ 17.585472] read descriptors

[ 17.585519] read strings

[ 17.591734] type=1400 audit(1532481716.452:17): avc: denied { getattr } for pid=2624 comm="sh" path="/system/bin/toybox" dev="dm-0" ino=412 scontext=u:r:gfxd:s0 tcontext=u:object_r:toolbox_exec:s0 tclass=file permissive=1

[ 17.596589] type=1400 audit(1532481716.452:18): avc: denied { execute } for pid=2624 comm="sh" name="toybox" dev="dm-0" ino=412 scontext=u:r:gfxd:s0 tcontext=u:object_r:toolbox_exec:s0 tclass=file permissive=1

[ 17.596672] type=1400 audit(1532481716.452:19): avc: denied { read open } for pid=2624 comm="sh" path="/system/bin/toybox" dev="dm-0" ino=412 scontext=u:r:gfxd:s0 tcontext=u:object_r:toolbox_exec:s0 tclass=file permissive=1

[ 17.596758] type=1400 audit(1532481716.453:20): avc: denied { execute_no_trans } for pid=2624 comm="sh" path="/system/bin/toybox" dev="dm-0" ino=412 scontext=u:r:gfxd:s0 tcontext=u:object_r:toolbox_exec:s0 tclass=file permissive=1

[ 17.596957] type=1400 audit(1532481716.462:21): avc: denied { write } for pid=2624 comm="mkdir" name="/" dev="tmpfs" ino=8654 scontext=u:r:gfxd:s0 tcontext=u:object_r:system_data_file:s0 tclass=dir permissive=1

[ 17.597054] type=1400 audit(1532481716.462:22): avc: denied { add_name } for pid=2624 comm="mkdir" name="gfx_logs" scontext=u:r:gfxd:s0 tcontext=u:object_r:system_data_file:s0 tclass=dir permissive=1

[ 17.597125] type=1400 audit(1532481716.462:23): avc: denied { create } for pid=2624 comm="mkdir" name="gfx_logs" scontext=u:r:gfxd:s0 tcontext=u:object_r:system_data_file:s0 tclass=dir permissive=1

[ 17.607321] type=1400 audit(1532481716.472:24): avc: denied { execute_no_trans } for pid=2630 comm="sh" path="/system/vendor/bin/init_ftrace.sh" dev="dm-0" ino=2117 scontext=u:r:gfxd:s0 tcontext=u:object_r:system_file:s0 tclass=file permissive=1

[ 17.739685] healthd: BatteryCycleCountPath not found

[ 18.219698] type=1400 audit(1532481717.085:25): avc: denied { read } for pid=2619 comm=47465844204B6D7367204465746563 name="kmsg" dev="tmpfs" ino=1884 scontext=u:r:gfxd:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=1

[ 18.220075] type=1400 audit(1532481717.085:26): avc: denied { create } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 18.220231] type=1400 audit(1532481717.085:27): avc: denied { setopt } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 18.220345] type=1400 audit(1532481717.085:28): avc: denied { net_admin } for pid=2619 comm=47465844204D6F6E69746F72 capability=12 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=capability permissive=1

[ 18.220491] type=1400 audit(1532481717.086:29): avc: denied { bind } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 18.221330] type=1400 audit(1532481717.086:30): avc: denied { read } for pid=2619 comm=47465844204C6F674743 name="gfx_logs" dev="tmpfs" ino=9329 scontext=u:r:gfxd:s0 tcontext=u:object_r:system_data_file:s0 tclass=dir permissive=1

[ 18.222346] type=1400 audit(1532481717.086:31): avc: denied { open } for pid=2619 comm=47465844204C6F674743 path="/data/gfx_logs" dev="tmpfs" ino=9329 scontext=u:r:gfxd:s0 tcontext=u:object_r:system_data_file:s0 tclass=dir permissive=1

[ 18.225344] type=1400 audit(1532481717.087:32): avc: denied { open } for pid=2619 comm=47465844204B6D7367204465746563 path="/dev/kmsg" dev="tmpfs" ino=1884 scontext=u:r:gfxd:s0 tcontext=u:object_r:kmsg_device:s0 tclass=chr_file permissive=1

[ 18.226634] type=1400 audit(1532481717.087:33): avc: denied { syslog_read } for pid=2619 comm=47465844204B6D7367204465746563 scontext=u:r:gfxd:s0 tcontext=u:r:kernel:s0 tclass=system permissive=1

[ 18.226711] type=1400 audit(1532481717.088:34): avc: denied { write } for pid=2619 comm=47465844204C6F6763617420446574 name="logdr" dev="tmpfs" ino=8666 scontext=u:r:gfxd:s0 tcontext=u:object_r:logdr_socket:s0 tclass=sock_file permissive=1

[ 18.226782] type=1400 audit(1532481717.088:35): avc: denied { connectto } for pid=2619 comm=47465844204C6F6763617420446574 path="/dev/socket/logdr" scontext=u:r:gfxd:s0 tcontext=u:r:logd:s0 tclass=unix_stream_socket permissive=1

[ 18.491551] type=1400 audit(1532481717.356:36): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 18.547529] bio: create slab <bio-2> at 2

[ 18.850414] EXT4-fs (dm-1): Ignoring removed nomblk_io_submit option

[ 18.863563] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit

[ 18.863615] SELinux: initialized (dev dm-1, type ext4), uses xattr

[ 18.863782] fs_mgr: check_fs(): mount(/dev/block/dm-1,/data,ext4)=0: Success

[ 18.868686] fs_mgr: check_fs(): unmount(/data) succeeded

[ 18.868772] fs_mgr: Running /system/bin/e2fsck on /dev/block/dm-1

[ 19.596457] e2fsck: e2fsck 1.42.9 (28-Dec-2013)

[ 19.596457]

[ 19.596518] e2fsck: Pass 1: Checking inodes, blocks, and sizes

[ 19.596518]

[ 19.596553] e2fsck: Pass 2: Checking directory structure

[ 19.596553]

[ 19.596603] e2fsck: Pass 3: Checking directory connectivity

[ 19.596603]

[ 19.596654] e2fsck: Pass 4: Checking reference counts

[ 19.596654]

[ 19.596705] e2fsck: Pass 5: Checking group summary information

[ 19.596705]

[ 19.596757] e2fsck: /dev/block/dm-1: 2274/3637248 files (10.2% non-contiguous), 369293/14531072 blocks

[ 19.596757]

[ 19.601460] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: discard,noauto_da_alloc,errors=panic

[ 19.601518] SELinux: initialized (dev dm-1, type ext4), uses xattr

[ 19.601618] fs_mgr: __mount(source=/dev/block/dm-1,target=/data,type=ext4)=0

[ 19.603172] init: (Loading properties from /data/local.prop took 0.00s.)

[ 19.637590] init: Starting service 'logd-reinit'...

[ 19.645838] init: Starting service 'ap_log_srv'...

[ 19.649641] logd.daemon: reinit

[ 19.649802] init: Not bootcharting.

[ 19.653616] init: Service 'logd-reinit' (pid 2721) exited with status 0

[ 19.705911] init: Starting service 'exec 3 (/system/bin/tzdatacheck)'...

[ 19.711143] init: Starting service 'apk_logfs'...

[ 19.711934] init: Service 'ap_log_srv' (pid 2722) exited with status 0

[ 19.730886] init: Service 'exec 3 (/system/bin/tzdatacheck)' (pid 2728) exited with status 0

[ 19.734989] init: Service wlan_prov does not have a SELinux domain defined.

[ 21.318963] type=1400 audit(1532481720.183:37): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 24.771743] init: Starting service 'exec 4 (/system/bin/bootstat)'...

[ 24.786397] init: Service 'exec 4 (/system/bin/bootstat)' (pid 2743) exited with status 0

[ 24.787414] init: cannot find '/system/bin/update_verifier' (No such file or directory), disabling 'exec 5 (/system/bin/update_verifier)'

[ 24.801638] init: Starting service 'flash_recovery'...

[ 24.802222] init: Service wlan_prov does not have a SELinux domain defined.

[ 24.810336] init: Starting service 'msync'...

[ 24.810982] init: Starting service 'coreu'...

[ 24.811692] init: Starting service 'mcud'...

[ 24.812407] init: Starting service 'dmiinfo'...

[ 24.813047] init: Starting service 'hdcpd'...

[ 24.813765] init: Starting service 'zygote'...

[ 24.814432] init: Starting service 'zygote_secondary'...

[ 24.815054] init: Starting service 'audioserver'...

[ 24.815792] init: Starting service 'cameraserver'...

[ 24.816521] init: Starting service 'drm'...

[ 24.817698] init: Starting service 'installd'...

[ 24.818691] init: Starting service 'keystore'...

[ 24.819658] init: couldn't write 2750 to /sys/fs/cgroup/stune/foreground/tasks: No such file or directory

[ 24.819886] init: Starting service 'mediacodec'...

[ 24.820468] init: Starting service 'mediadrm'...

[ 24.822599] init: Starting service 'mediaextractor'...

[ 24.823203] init: Starting service 'media'...

[ 24.823714] init: Starting service 'netd'...

[ 24.824219] init: Starting service 'init_modem'...

[ 24.824744] init: Starting service 'pstore-clean'...

[ 24.825336] init: Starting service 'crashlogd'...

[ 24.825847] init: Starting service 'log-watch'...

[ 24.826405] init: Starting service 'gatekeeperd'...

[ 24.827488] type=1400 audit(1532481723.688:38): avc: denied { create } for pid=2747 comm="init" name="mcud" scontext=u:r:init:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1

[ 24.827770] type=1400 audit(1532481723.688:39): avc: denied { setattr } for pid=2747 comm="init" name="mcud" dev="tmpfs" ino=10487 scontext=u:r:init:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1

[ 24.840992] init: Starting service 'perfprofd'...

[ 24.844302] init: Starting service 'power_hal_helper'...

[ 24.867141] type=1400 audit(1532481723.732:40): avc: denied { search } for pid=2748 comm="dmiinfo" name="entries" dev="sysfs" ino=17044 scontext=u:r:dmiinfo:s0 tcontext=u:object_r:dmi_entries_files:s0 tclass=dir permissive=1

[ 24.875788] init: avc: denied { set } for property=devinfo.sys.manufacturer pid=2748 uid=0 gid=0 scontext=u:r:dmiinfo:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1

[ 24.896225] init: Service 'pstore-clean' (pid 2764) exited with status 1

[ 24.899780] init: Service 'dmiinfo' (pid 2748) exited with status 0

[ 24.904211] type=1400 audit(1532481723.767:41): avc: denied { read } for pid=2747 comm="mcud" name="psched" dev="proc" ino=4026532019 scontext=u:r:mcud:s0 tcontext=u:object_r:proc_net:s0 tclass=file permissive=1

[ 24.904350] type=1400 audit(1532481723.767:42): avc: denied { open } for pid=2747 comm="mcud" path="/proc/2747/net/psched" dev="proc" ino=4026532019 scontext=u:r:mcud:s0 tcontext=u:object_r:proc_net:s0 tclass=file permissive=1

[ 24.904424] type=1400 audit(1532481723.767:43): avc: denied { getattr } for pid=2747 comm="mcud" path="/proc/2747/net/psched" dev="proc" ino=4026532019 scontext=u:r:mcud:s0 tcontext=u:object_r:proc_net:s0 tclass=file permissive=1

[ 24.914313] init: avc: denied { set } for property=sys.modem pid=2772 uid=0 gid=1001 scontext=u:r:init_modem:s0 tcontext=u:object_r:system_prop:s0 tclass=property_service permissive=1

[ 24.935302] init: Service 'init_modem' (pid 2763) exited with status 0

[ 24.962839] init: Service 'power_hal_helper' (pid 2769) exited with status 0

[ 25.061546] type=1400 audit(1532481723.926:44): avc: denied { call } for pid=2749 comm="hdcpd" scontext=u:r:hdcpd:s0 tcontext=u:r:coreu:s0 tclass=binder permissive=1

[ 25.061962] type=1400 audit(1532481723.926:45): avc: denied { use } for pid=2746 comm="coreu" path="/dev/ashmem" dev="tmpfs" ino=1912 scontext=u:r:hdcpd:s0 tcontext=u:r:coreu:s0 tclass=fd permissive=1

[ 25.351303] type=1400 audit(1532481724.216:46): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 25.545497] init: Service 'flash_recovery' (pid 2744) exited with status 0

[ 25.880620] atomisp-css2401a0_v21 0000:00:03.0: Refused to change power state, currently in D3

[ 25.900875] ov5693_s_power: on 0

[ 25.908188] PANEL_ID_1=1

[ 25.908205] type=1400 audit(1532481724.773:47): avc: denied { search } for pid=2753 comm="cameraserver" name="panel_id" dev="sysfs" ino=16079 scontext=u:r:cameraserver:s0 tcontext=u:object_r:panel_id_files:s0 tclass=dir permissive=1

[ 25.908277] PANEL_ID_2=1

[ 25.908327] PANEL_ID_3=1

[ 25.908331] type=1400 audit(1532481724.773:48): avc: denied { read } for pid=2753 comm="cameraserver" name="panel_id_num" dev="sysfs" ino=16080 scontext=u:r:cameraserver:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 25.908430] PANEL_ID_4=1

[ 25.908480] >>>> get_panel_id : PANEL_ID_NUM=0xf

[ 25.921210] type=1400 audit(1532481724.773:49): avc: denied { open } for pid=2753 comm="cameraserver" path="/sys/kernel/panel_id/panel_id_num" dev="sysfs" ino=16080 scontext=u:r:cameraserver:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 25.924950] type=1400 audit(1532481724.774:50): avc: denied { getattr } for pid=2753 comm="cameraserver" path="/sys/kernel/panel_id/panel_id_num" dev="sysfs" ino=16080 scontext=u:r:cameraserver:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 26.324992] type=1400 audit(1532481725.190:51): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 28.924987] warning: `main' uses 32-bit capabilities (legacy support in use)

[ 30.042932] >>>> ec_touch_vibrator_setup() : enable VIB

[ 30.043731] >>>> ec_suspend_notify() : leave suspend

[ 32.175618] PANEL_ID_1=1

[ 32.175655] PANEL_ID_2=1

[ 32.175704] PANEL_ID_3=1

[ 32.175755] PANEL_ID_4=1

[ 32.175806] >>>> get_panel_id : PANEL_ID_NUM=0xf

[ 32.176266] type=1400 audit(1532481731.041:52): avc: denied { search } for pid=3038 comm="system_server" name="panel_id" dev="sysfs" ino=16079 scontext=u:r:system_server:s0 tcontext=u:object_r:panel_id_files:s0 tclass=dir permissive=1

[ 32.176725] type=1400 audit(1532481731.041:53): avc: denied { read } for pid=3038 comm="system_server" name="panel_id_num" dev="sysfs" ino=16080 scontext=u:r:system_server:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 32.176801] type=1400 audit(1532481731.041:54): avc: denied { open } for pid=3038 comm="system_server" path="/sys/kernel/panel_id/panel_id_num" dev="sysfs" ino=16080 scontext=u:r:system_server:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 32.176887] type=1400 audit(1532481731.041:55): avc: denied { getattr } for pid=3038 comm="system_server" path="/sys/kernel/panel_id/panel_id_num" dev="sysfs" ino=16080 scontext=u:r:system_server:s0 tcontext=u:object_r:panel_id_files:s0 tclass=file permissive=1

[ 32.230624] [1511]sensor_enable_store accel_b

[ 32.230671] [1516]sensor_enable_store 0

[ 32.230719] [676]sensor_disable accel_b

[ 32.230889] [1511]sensor_enable_store cm32181

[ 32.231039] [1516]sensor_enable_store 0

[ 32.231082] [676]sensor_disable cm32181

[ 32.231357] [1511]sensor_enable_store gyro

[ 32.231393] [1516]sensor_enable_store 0

[ 32.231443] [676]sensor_disable gyro

[ 32.441545] type=1400 audit(1532481731.307:56): avc: denied { write } for pid=3038 comm="McudConnector" name="mcud" dev="tmpfs" ino=10487 scontext=u:r:system_server:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1

[ 32.441707] type=1400 audit(1532481731.307:57): avc: denied { connectto } for pid=3038 comm="McudConnector" path="/dev/socket/mcud" scontext=u:r:system_server:s0 tcontext=u:r:mcud:s0 tclass=unix_stream_socket permissive=1

[ 33.309091] acc_open

[ 33.309140] acc_release

[ 33.667096] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts

[ 33.667446] type=1400 audit(1532481732.532:58): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 33.669028] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts

[ 33.672142] SELinux: initialized (dev fuse, type fuse), uses genfs_contexts

[ 34.211302] init: avc: denied { set } for property=apos.production.mode pid=3038 uid=1000 gid=1000 scontext=u:r:system_server:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1

[ 34.276659] init: Service 'bootanim' (pid 2605) exited with status 0

[ 34.277370] init: Starting service 'exec 6 (/system/bin/bootstat)'...

[ 34.290716] init: Service 'exec 6 (/system/bin/bootstat)' (pid 3310) exited with status 0

[ 34.291066] init: Starting service 'exec 7 (/system/bin/bootstat)'...

[ 34.300787] init: Service 'exec 7 (/system/bin/bootstat)' (pid 3313) exited with status 0

[ 34.301116] init: Starting service 'exec 8 (/system/bin/bootstat)'...

[ 34.316912] init: Service 'exec 8 (/system/bin/bootstat)' (pid 3318) exited with status 0

[ 34.317202] init: Starting service 'exec 9 (/system/bin/bootstat)'...

[ 34.341031] init: Service 'exec 9 (/system/bin/bootstat)' (pid 3321) exited with status 0

[ 34.389822] type=1400 audit(1532481733.255:59): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 34.699142] rtk_btusb: btchr_open: BT usb char device is opening

[ 34.703092] rtk_btusb: btchr_ioctl DOWN_FW_CFG with Cmd:1074022601

[ 34.703134] rtk_btusb: get_firmware: start, cached 1,patch_entry->fw_len= 0

[ 34.703179] rtk_btusb: load_firmware: Default lmp version = 0x8821, config file name[rtl8821a_config], fw file name[rtl8821a_fw]

[ 34.704433] rtk_btusb: rtk_update_altsettings: 1 AltSettings

[ 34.704473] rtk_btusb: ORG Config len=00000015:

[ 34.704473]

[ 34.704525] rtk_btusb: 00000000: 55 ab 23 87 0f 00 f4 00 08 01 00 00 00 05 50 00

[ 34.704525]

[ 34.704575] rtk_btusb: 00000010: 00 db 00 01 42 00 00 00 00 00 00 00 00 00 00 00

[ 34.704575]

[ 34.704639] rtk_btusb: No Mac Config for BT

[ 34.704639]

[ 34.704676] rtk_btusb: Final Config len=00000015:

[ 34.704676]

[ 34.704729] rtk_btusb: 00000000: 55 ab 23 87 0f 00 f4 00 08 01 00 00 00 05 50 00

[ 34.704729]

[ 34.704779] rtk_btusb: 00000010: 00 db 00 01 42 00 00 00 00 00 00 00 00 00 00 00

[ 34.704779]

[ 34.706730] rtk_btusb: load_firmware: epatch_buf = vmalloc(fw->size, GFP_KERNEL)

[ 34.711871] [1511]sensor_enable_store accel_b

[ 34.711910] [1516]sensor_enable_store 1

[ 34.711960] [661]sensor_enable accel_b

[ 34.717230] [1146]sensor_launch_work accel_b

[ 34.766657] rtk_btusb: reset_channel: status 0

[ 35.066848] rtk_btusb: reset_channel: Wait channel reset for 300ms

[ 35.067649] rtk_btusb: get_eversion: status 0, eversion 1

[ 35.067687] rtk_btusb: load_firmware: Default lmp_version 0x8821, project_id[2] 0x8821 -> match

[ 35.067738] rtk_btusb: BTCOEX:20150921-0x6158 svn version:0x0000418c fw version:0x0e5bbeca rtk_btusb version:4.1.4 Cut:2, patch length:0x5d10, patch offset:0x00004300

[ 35.067738]

[ 35.067857] rtk_btusb: load_firmware: vfree(epatch_buf)

[ 35.067896] rtk_btusb: load_firmware: fw exists, config file exists

[ 35.068660] rtk_btusb: check_fw_version: Controller lmp = 0xdd3a, patch lmp = 0xdd3a, default patch lmp = 0x8821

[ 35.068701] rtk_btusb: check_fw_version: Warm BT controller startup with same lmp

[ 35.068762] rtk_btusb: btusb_open: Start, PM usage count 0

[ 35.068867] rtk_btusb: btusb_open: End, PM usage count 0

[ 36.352930] type=1400 audit(1532481735.217:60): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

[ 37.386105] type=1400 audit(1532481736.251:61): avc: denied { read } for pid=2619 comm=47465844204D6F6E69746F72 scontext=u:r:gfxd:s0 tcontext=u:r:gfxd:s0 tclass=netlink_kobject_uevent_socket permissive=1

cht_rvp:/ #

Cherry Trail Z8750 USB3.0 xhci Compatibility USB3.0 flash issue on Android 7.1

Trending Articles

Practice Sheet of Right form of verbs for HSC Students

Download: FK ft Shenky – Nakuyewa ”Prod by: Shenky”

How to win at Markstrat (Markstrat Tips and Tricks) – Vodites

Ominde Commission Report and Recommendations – Ominde Report of 1964

Bureau of Internal Revenue: Regional Offices (Directory)

GO 53 on Enhancement of Ex-gratia upto 5 Lakhs Toddy Tappers in Telangana

Cakewalk CA-2A Leveling Amplifier v2.0.1.97 WiN, v2.0.1.96 OSX Incl Keygen

Mp3 Download: Mdu - Kunjenjenjena

How the kill the job , when DTP request running for long hours.

Microsoft Intune から展開しているアプリのアップデートについて

18-year-old girl was beaten for half an hour by two Northampton men in 'an...

Car crash in Dunton Bassett leaves driver in critical condition

Macky 2, Two Others In Road Accident

Application log 00000000000000089514: Could not convert queue DLVST90CLNT

Detroit mafia: D’Anna Brothers agree to plea deal

Delivery block field greyed out using VA02

Muloraki Au

【個人撮影】スマホのプライベート映像♪「中に出さないで///」カラオケ屋での生ハメ撮りが流出ｗ【リベンジポルノ】＠PornHub

BREAKING NEWS: Diamond Platnumz Is Reported Dead After Ghastly Car Accident

FIAT 500 B0111 B0112